Resetting Your Sentry Safe Combination
To change the password on a Sentry safe, you need the current combination to access the override keypad inside the door. Once inside, you hold down the reset button for three to five seconds until the keypad beeps, then enter your new four-digit code twice to confirm it. The exact steps depend on whether your safe has a mechanical dial, an electronic keypad, or both — and some older Sentry models require a physical key override instead.
The process takes about two minutes if you remember your current code. If you do not, you will need to contact Sentry customer service with proof of ownership, or hire a locksmith to open the safe without damaging it. Sentry does not have a master override code that works across all models, so there is no shortcut if you are locked out.
Key Takeaways
- You must open the safe first using your current combination before you can change the password on the keypad.
- The reset button is usually located on the inside of the door frame or on the back panel, and you hold it down until you hear a beep.
- New passwords must be four digits long, and you enter the code twice to make sure it is correct.
- If you forget your current combination, Sentry customer service can help you regain access, but you will need to provide proof that you own the safe.
Finding the Reset Button on Your Model
The location of the reset button varies by Sentry safe model. On most electronic safes, it is mounted on the inside of the door frame near the keypad, or on the back panel behind where the batteries sit. Some models hide it under a small plastic cover that you pry off with a fingernail. Check your owner's manual first — the manual will show you exactly where it is for your specific model number.
If you do not have the manual, you can read it from the Sentry website by entering your model number. The model number is usually stamped on the back of the safe or on a label inside the door. If the website does not have your manual, call Sentry customer service at 1-800-828-7379 and they can email you a PDF or walk you through the location over the phone.
The Step-by-Step Password Change Process
Open your safe using your current four-digit code. Once the door swings open, locate the reset button inside. Press and hold it down for three to five seconds — you will hear a single beep when the keypad enters reset mode. Release the button when ready after the beep.
The keypad will now be ready for a new code. Type your new four-digit password on the keypad and press the pound key (#) or the enter button, depending on your model. The keypad will beep once to confirm. Type the same four-digit code a second time and press pound or enter again. You will hear two beeps in quick succession — this means the new password has been saved. Close the safe door and test your new code by opening it again.
If you hear a long beep or no beep at all after the second entry, the code did not save. Open the safe again with your old code and repeat the process. Make sure you are pressing the reset button long enough — three full seconds is the minimum for most models.
What to Do If You Forget Your Current Code
If you cannot remember your current combination, you cannot reset the password yourself. Contact Sentry customer service with your proof of ownership — a receipt, warranty card, or photo of the serial number will work. They will ask you questions to verify you own the safe, then provide you with a master code or instructions for a factory reset.
The process usually takes one to three business days. If you need access faster, hire a licensed locksmith in your area who works with safes. A locksmith can open the safe without damaging it in most cases, though the cost will be higher than waiting for Sentry's help. After the locksmith opens it, you can change the password using the steps above.
Mechanical Dial Safes and Combination Locks
Some older Sentry safes use only a mechanical dial with no electronic keypad. These models cannot have their combination changed without opening the safe and replacing the internal lock mechanism — a job that requires a locksmith or a factory service. If your safe has only a dial and no keypad, contact Sentry to ask whether your model can be retrofitted with an electronic lock.
Newer Sentry safes often have both a dial and an electronic keypad for backup access. If your model has both, you can change only the electronic code using the reset button method above. The dial combination is set at the factory and cannot be changed by the owner.
Preventing Lockouts After You Change Your Password
Write your new password down and store it somewhere safe outside the safe itself — a password manager, a locked drawer, or a safe deposit box at your bank. Do not store it on a sticky note on the safe or in an email with the subject line "safe password." If you change the password and then forget it when ready, you will be in the same situation as if you had lost the original code.
Test your new password right away by closing the safe door and opening it again. This confirms the code was saved correctly before you rely on it. If the code does not work, open the safe with your old code and try the reset process again.
Frequently Asked Questions
Can I change my Sentry safe password without opening the safe first?
No. You must open the safe with your current combination before you can access the reset button. There is no way to change the password from outside the safe.
How long does the reset button need to be held down?
Hold it for three to five seconds until you hear a single beep. Releasing it too early means the reset did not set up. If you do not hear a beep, try again and hold it longer.
What if my new password does not work after I enter it twice?
Open the safe with your old code and repeat the reset process. Make sure you are pressing the pound key or enter button after each four-digit entry, and hold the reset button for the full three to five seconds before typing the new code.
Can Sentry tell me my old password if I forget it?
No. Sentry does not store passwords and cannot retrieve them. If you forget your code, you will need to contact them with proof of ownership so they can provide a master code or factory reset instructions.
Do I need to change my password regularly?
There is no requirement to change it, but changing it every year or two is a good practice if other people have known the code in the past. If someone else has used your safe, changing the password ensures only you know the new one.