What you're actually doing when you install a modem and router

Your modem connects to your internet service provider's network and converts that signal into something your devices can use. Your router takes that signal and broadcasts it wirelessly to your phone, laptop, and other devices. Installing them means plugging in cables in a specific order, then logging into each device to change the default password — which is the security step that actually matters.

The physical installation takes about ten minutes. The security part takes another five. Most people skip the security part and then wonder why their network feels slow or why they see unfamiliar devices connected to it.

Key Takeaways

  • Your modem connects to the wall jack and the router; your router broadcasts the wireless signal to your devices.
  • Always change the default admin password on both your modem and router before you do anything else on the network.
  • The router's default password is usually printed on a sticker on the back; write it down before you start, because you will need it to log in.
  • If your modem and router are combined into one device, you still need to change the default password and update the firmware when prompted.
  • Restart your modem first, then your router, and wait two minutes between restarts so the modem can reconnect to your provider's network.

Physical setup: where each cable goes

Start with the modem. Locate the coaxial cable (the thick cable with a metal connector) that comes from the wall jack — this is your internet line from the provider. Screw it onto the port labeled "Cable In" or "Internet In" on the back of the modem. Do not force it; hand-tight is enough.

Next, take an ethernet cable (a thin cable that looks like a phone cord but wider) and plug one end into the port on the modem labeled "Ethernet" or "LAN". Plug the other end into the port on the router labeled "WAN", "Internet", or "Uplink" — check your router's manual if you are unsure which port. This cable carries the internet signal from the modem to the router.

Plug the modem's power cable into an outlet, then plug the router's power cable into a separate outlet. Wait 30 seconds. The modem will take about 60 to 90 seconds to boot up; you will see lights turn on and then stabilize. Once the modem's lights stop blinking rapidly, restart the router by unplugging it for 10 seconds, then plugging it back in. Wait another two minutes before moving forward.

Finding the router's default password and logging in

Look at the back or bottom of your router for a sticker with the default network name (called the SSID) and password. Write both down on a piece of paper right now — you will need the password in the next step, and if you lose it, resetting the router means redoing this entire process.

Open a web browser on your phone or laptop and type the router's IP address into the address bar. This is usually 192.168.1.1 or 192.168.0.1, but check your router's manual or the sticker on the back if neither works. You will see a login page asking for a username and password. The username is usually admin and the password is the one from the sticker.

Once you are logged in, look for a section called "Administration", "Settings", or "Advanced". Find the option to change the admin password — this is different from the Wi-Fi password. Change it to something you will remember but that is not your name, birthday, or address. Write this new password down and store it somewhere safe, like a password manager or a locked drawer. You will need it if you ever need to log back into the router.

Changing the Wi-Fi password from the default

While you are still logged into the router, look for a section called "Wireless", "Wi-Fi", or "Network". You will see the network name (SSID) that was printed on the sticker. Change this to something you recognize — you can keep it straightforward, like "Home Network" or your last name. Do not include personal information like your address or phone number.

Find the Wi-Fi password field and change it from the default to something new. Use at least 12 characters and mix uppercase letters, lowercase letters, numbers, and symbols — something like BlueMoon#2024Home is much stronger than password123. Write this password down and keep it somewhere you can find it, because you will need to give it to anyone who wants to connect to your network.

Save these changes. The router will restart, which takes about 30 to 60 seconds. Your devices will disconnect from the network briefly. When the router comes back online, you can reconnect using the new Wi-Fi password.

Checking your modem's default password

Your modem also has a default admin password, and you should change it too. Open a browser and type the modem's IP address — this is usually 192.168.100.1 or printed on the modem itself. Log in with the default username and password (usually admin and motorola, admin, or password, depending on the brand).

Look for "Administration" or "Advanced Settings" and change the admin password to something different from your router password. Write it down and store it safely. You rarely need to log into the modem after this, but if your internet stops working and your provider asks you to check the modem's status, you will need this password.

Some modems prompt you to update the firmware (the modem's internal software) when you first log in. If you see this option, do it now. Firmware updates patch security holes and improve performance. The update takes five to ten minutes and the modem will restart when it is done.

Testing your connection and checking for intruders

Once everything has restarted, open a web browser and try to load a website — Google.com works fine. If the page loads, your modem and router are talking to each other and your internet is working.

Next, log back into your router and look for a section called "Connected Devices", "Device List", or "DHCP Clients". This shows every device currently connected to your network. You should see your phone, laptop, and any other devices you intentionally connected. If you see devices you do not recognize, someone else is using your network. Change your Wi-Fi password when ready and check your router's manual for how to block specific devices.

If your internet is not working, restart the modem first (unplug it for 10 seconds, plug it back in, wait two minutes), then restart the router. If it still does not work, contact your internet provider — they can check whether the modem is properly registered on their network.

Modem and router combined in one device

Some providers give you a single device that acts as both modem and router. The setup is the same: plug in the coaxial cable from the wall, plug in the power cable, and wait for it to boot up. Then log in using the default password from the sticker and change both the admin password and the Wi-Fi password.

The main difference is that you cannot separate the modem from the router if one fails. If the device stops working, you have to replace the whole thing. Some people prefer to use their own separate modem and router instead, which gives them more control and lets them replace just the part that breaks. Check with your provider first — some require you to use their device, while others let you bring your own.

Frequently Asked Questions

What if I forgot the default Wi-Fi password before I changed it?

You can reset the router to factory settings by holding down the reset button (usually a small hole on the back) for 10 to 15 seconds. This erases all your changes, including the new passwords you set. You will have to log in with the default password again and redo the security steps. To avoid this, write down the default password before you start.

Do I need to change the Wi-Fi password if I live alone?

Yes. The default password is the same for every router of that model, so anyone who knows the brand can guess it. Changing it takes five minutes and prevents neighbors or passersby from connecting to your network and using your internet.

Why does my internet keep dropping after I installed everything?

The most common cause is that the ethernet cable between the modem and router is loose. Unplug it from both ends and plug it back in firmly. If that does not work, try a different ethernet cable — the original one may be damaged. If the problem continues, restart the modem and wait the full two minutes before restarting the router.

Can I put my modem and router anywhere in the house?

The modem must stay near the wall jack where the coaxial cable comes in. The router can go anywhere, but it works better in a central location away from metal objects and thick walls. Avoid putting it in a closet or cabinet, because the walls block the wireless signal. A shelf in an open room usually works best.

What if my router keeps asking me to update the firmware?

Let it update. Firmware updates patch security holes that hackers can exploit. Updates usually take 10 to 15 minutes and the router will restart when done. Do not unplug the router during an update, or it may stop working entirely.