You can make an Ethernet cable yourself with the right tools and about ten minutes of practice

A finished Ethernet cable costs between $5 and $15 depending on length, but making one costs roughly $1 to $3 in materials. More importantly, you control the exact length — no excess cable coiled behind equipment, no cable too short to reach. If you already have a crimper and know which wires go where, the actual assembly takes five minutes.

The process is straightforward: strip the outer jacket, arrange eight colored wires in the correct order, insert them into a connector, and crimp it down. The hardest part is getting the wire order right the first time. This guide walks you through both the standard order and what happens if you reverse it.

Key Takeaways

  • You need a crimper, RJ45 connectors, and bulk Ethernet cable — all available at hardware stores or online for under $20 total.
  • The two standard wire orders are T568A and T568B; most home networks use T568B on both ends, but the order matters only if both ends match.
  • Strip about half an inch of the outer jacket, arrange the wires, push them fully into the connector, and crimp with steady pressure until you hear a click.
  • Test the cable with a network tester or by plugging it in — a cable with wires in the wrong order straightforward will not work, but it will not damage anything.

Tools and materials you actually need

A crimper is the only tool you cannot skip. It looks like a pliers with a small rectangular die at the end. Buy one rated for RJ45 connectors; they cost $8 to $20 and work for hundreds of cables. Do not try to crimp by hand or with regular pliers — the connector will not seat properly and the cable will fail intermittently.

RJ45 connectors are the small plastic plugs that go on the cable end. They come in packs of 50 or 100 for $5 to $10. Buy more than you think you need; the first few will likely fail as you learn the process. Bulk Ethernet cable comes in spools of 100 feet or 1000 feet. A 100-foot spool costs $15 to $25. Category 5e cable works for most home networks; Category 6 is slightly more durable but costs more and is overkill for residential use.

A cable stripper makes removing the outer jacket easier, but a utility knife works if you are careful. A network tester — a small device that lights up to show whether each wire is in the right place — costs $10 to $30 and saves time troubleshooting. It is optional but useful if you plan to make more than three cables.

The two wire orders and which one to use

Ethernet cables contain eight wires twisted into four pairs. The order in which you arrange them at the connector determines whether the cable works. The two standard orders are called T568A and T568B. For a home network, use T568B on both ends — this is the most common standard and the one your router and devices expect.

T568B order from left to right is: orange-white, orange, green-white, blue, blue-white, green, brown-white, brown. Write this down or take a photo before you start. The wires are thin and the colors are straightforward to mix up under poor light.

What matters is that both ends of the cable use the same order. If one end is T568A and the other is T568B, the cable will not work — the wires will be crossed and data cannot flow. If both ends are T568B, or both are T568A, the cable works fine. Most cables you buy are T568B on both ends, so stick with that.

Step-by-step assembly

Step 1: Cut and strip the cable. Measure the length you need and cut the cable with a utility knife or cable cutter. Leave a few extra inches for mistakes. Hold the cable steady and carefully cut through the outer plastic jacket about half an inch from the end. Rotate the cable as you cut so you slice the jacket evenly without nicking the wires inside. Peel the jacket away and discard it.

Step 2: Untwist and straighten the wires. The four pairs are twisted together. Untwist them gently — do not pull hard or you will break them. Straighten each wire and lay them flat on a table in front of you. This is the moment to arrange them in the correct order before they tangle again.

Step 3: Arrange wires in T568B order. Line up the wires left to right in this order: orange-white, orange, green-white, blue, blue-white, green, brown-white, brown. Hold them together at the end so they stay in order. Trim them so they are all the same length — about three-quarters of an inch from the jacket. Uneven wires will not all seat in the connector.

Step 4: Insert wires into the connector. Hold the RJ45 connector with the clip facing away from you and the open end toward you. Push the wires straight into the connector in order. They should slide in smoothly. Push until all eight wires are fully inserted and you can see the bare wire at the very front of the connector. If a wire does not go all the way in, remove all wires, trim them shorter, and try again.

Step 5: Crimp the connector. Place the connector in the crimper with the wires still inside. Squeeze the handles together with steady pressure. You will feel resistance, then a click as the crimper releases. This click means the metal contacts inside have pierced the wire insulation and made electrical contact. Remove the connector and inspect it — the wires should not move if you tug gently.

Step 6: Repeat on the other end. Cut, strip, and crimp the other end of the cable using the same T568B order. Both ends must match for the cable to work.

Testing your cable before you use it

Plug the cable into a network device and see if it works — that is the simplest test. If your computer or router recognizes the connection and data flows, the cable is good. If nothing happens, the wires are likely in the wrong order or not fully seated in the connector.

A network tester gives you more detail. Plug one end into the tester's input and the other end into the output. The tester lights up in sequence to show which wires are connected. If the lights match the T568B pattern, your cable is correct. If lights are out of order or missing, a wire is either in the wrong position or not making contact.

If a cable fails, do not assume the cable itself is bad — the connector is usually the problem. Cut off the bad connector, strip the cable again, and crimp a new one. Bulk cable rarely fails; bad crimps are almost always the cause.

Common mistakes and how to avoid them

The most common error is reversing the wire order at one end. You strip the cable, arrange the wires, crimp the first end, then forget which order you used and do the second end differently. Write down the order or take a photo. Better yet, crimp both ends before moving on to anything else.

The second mistake is not pushing wires all the way into the connector. If a wire sits even slightly short, it will not make contact. The connector has eight tiny metal contacts that must touch the bare copper. If the insulation is still in the way, no connection happens. Push until you see bare wire at the front.

The third mistake is using a crimper that is not rated for RJ45. Some crimpers are designed for telephone connectors or coaxial cable and will not work. Check the package before you buy — it must say RJ45 or Ethernet.

When to buy a cable instead of making one

If you need only one or two cables, buying them finished costs less in time and frustration. A pre-made cable costs $5 to $15 and arrives ready to use. Making cables makes sense when you need five or more, or when you need an unusual length that stores do not stock.

If you are uncomfortable with small tools or have limited dexterity, buying finished cables is the better choice. The crimper requires steady hands and moderate grip strength. A cable that fails intermittently is harder to troubleshoot than a cable that does not work at all, so if you are unsure about your technique, a store-bought cable is more reliable.

Frequently Asked Questions

Can I use T568A instead of T568B?

Yes. T568A works just as well as T568B for home networks. The only rule is that both ends of the cable must use the same order. If you use T568A on both ends, the cable works fine. Most cables are T568B, so stick with that unless you have a reason to switch.

What happens if I get the wire order wrong?

The cable straightforward will not work. Your device will not recognize a connection. The cable will not damage your equipment — it just will not transmit data. Cut off the bad connector and crimp a new one with the correct wire order.

How long does a homemade cable last?

A properly crimped cable lasts as long as a store-bought one — years of daily use. The weak point is the connector, not the cable. If a cable fails after months of use, the connector is usually loose or corroded, not the cable itself.

Do I need a network tester?

No. Plug the cable in and see if it works. A tester is helpful if you make many cables or if a cable fails and you need to know which wire is the problem. For one or two cables, just test by using them.

Can I make a cable longer than 100 feet?

Ethernet cables lose signal strength over distance. The maximum recommended length is 100 meters (about 330 feet) for standard Ethernet. For a home network, stay under 100 feet. If you need longer distances, use a network switch or repeater to boost the signal.