The basic connection: what goes where
Your modem receives internet from your provider's cable or fiber line. Your router takes that internet from the modem and broadcasts it wirelessly to your devices. To connect them, you run an ethernet cable from the port labeled "Ethernet" or "LAN" on the back of your modem into the port labeled "WAN," "Internet," or sometimes "Uplink" on the back of your router. That single cable is the entire physical connection — nothing else plugs in between them.
The modem and router are separate devices for a reason. The modem speaks to your provider's network. The router speaks to your devices. Keeping them separate means you can restart one without restarting the other, and you can replace a failing router without calling your provider. If your modem and router are built into a single device (called a gateway), you skip this step entirely — they are already connected inside.
Before you plug anything in, turn off both the modem and router. This prevents electrical stress when the cable makes contact. You do not need to do this for safety, but it reduces the chance of a port getting damaged.
Key Takeaways
- Run one ethernet cable from the modem's LAN port to the router's WAN or Internet port — this is the only physical connection needed.
- Turn off both devices before connecting the cable, then power on the modem first and wait for its lights to stabilize before powering on the router.
- The router's setup page appears at 192.168.1.1 or 192.168.0.1 in your browser once it has booted, and this is where you name your network and set a password.
- If the router does not get an internet light or connection after five minutes, restart the modem first, then the router, and wait another five minutes.
- A gateway device (modem and router combined) skips this connection step because the two are already wired inside the same box.
Powering on in the right order
After the cable is connected, power on the modem first. Wait for its lights to stop changing — you will see lights labeled "Power," "Internet," "Online," or "Downstream" blink and then settle into a steady state. This usually takes one to three minutes. The modem is telling your provider's network that it is ready to receive internet.
Only after the modem's lights have settled should you power on the router. The router will search for internet from the modem. You will see its lights blink as it boots. Wait another two to three minutes for the router's lights to settle. Once they do, the router has found the modem's internet and is ready to broadcast your wireless network.
If you power on the router before the modem is ready, the router will not find internet and may take longer to recover. Starting them in order — modem first, router second — is the fastest path to a working network.
Accessing the router's setup page
Once the router's lights have settled, open a web browser on any device connected to the router's wireless network (or connected to it by ethernet). Type 192.168.1.1 into the address bar and press Enter. If that does not work, try 192.168.0.1 instead. One of these two addresses is where almost every home router keeps its setup page.
You may be asked for a username and password. Check the sticker on the bottom or back of the router — it usually lists the default username (often "admin") and password. If you cannot find the sticker, the router's manual or the manufacturer's website will have the defaults. Write down these credentials somewhere safe; you will need them if you ever need to change your network settings later.
Once you are logged in, look for a section called "Wireless," "WiFi," "Network Name," or "SSID." This is where you name your network — the name that appears when you search for WiFi on your phone. Change it from the default (which is often the router model number) to something you will recognize. Then set a password at least 12 characters long, using a mix of uppercase, lowercase, numbers, and symbols. This password is what you will type on your devices to connect to the network.
Confirming the connection is working
After you have named your network and set a password, save the changes. The router will restart — its lights will blink again for a minute or two. Once they settle, try connecting a phone or laptop to the network using the password you just created. Open a web browser and visit any website. If the page loads, your modem and router are connected and working.
If a website does not load, check that you typed the password correctly. Passwords are case-sensitive, so "MyPassword" is different from "mypassword." If the password is correct but the internet still does not work, restart the modem (turn it off, wait 30 seconds, turn it back on), then restart the router the same way. Wait five minutes and try again.
If the router still shows no internet light after a restart, the cable between the modem and router may be loose or damaged. Unplug it from both ends, inspect it for visible damage, and plug it back in firmly. If the light still does not appear, try a different ethernet cable if you have one available.
Troubleshooting when the router does not see the modem
Sometimes the router powers on but shows no internet light, or the setup page says "No Internet Connection." This usually means the modem has not finished starting up, or the cable is not fully seated. The first step is always to wait — give the modem a full five minutes from when you powered it on. Its lights should show a steady "Online" or "Internet" indicator.
If five minutes have passed and the modem's lights are not steady, restart it: turn it off, wait 30 seconds, and turn it back on. While the modem restarts, unplug the ethernet cable from both the modem and router, inspect both ends, and plug it back in firmly. You should hear a small click as the connector seats. Then restart the router and wait another five minutes.
If the router still shows no internet after this, the issue may be with the modem itself or the line from your provider. Contact your internet provider's support line — they can check whether the modem is communicating with their network. Do not assume the router is broken; in most cases, the modem is the problem.
What to do if you have a gateway device
Some providers issue a single device that combines the modem and router into one box. This is called a gateway, and it handles both jobs internally. If you have a gateway, you do not need to run an ethernet cable between two devices — there is nothing to connect. You straightforward power it on and wait for its lights to settle, then access its setup page at 192.168.1.1 or 192.168.0.1 to name your network and set a password.
The advantage of a gateway is simplicity: fewer cables, fewer devices, one power cord. The disadvantage is that if the wireless part fails, you cannot replace just the router — you have to replace the entire gateway, which means a new modem too. If the modem part fails, you lose both internet and wireless at the same time. For this reason, many people prefer separate modem and router devices, even though they require one extra cable.
Frequently Asked Questions
Can I use any ethernet cable to connect the modem and router?
Yes. Any standard ethernet cable works, regardless of length or brand. Longer cables (50 feet or more) can occasionally cause problems on very old equipment, but for typical home setups, the cable length does not matter. Make sure both ends are fully plugged in — you should hear a click.
Do I need to restart my modem and router every time I restart my computer?
No. Restarting your computer does not affect the modem or router at all. They stay powered on and keep broadcasting your network. You only restart them if the internet stops working or if you are changing settings that require a restart.
What if my router has multiple ethernet ports on the back?
Your router has one WAN or Internet port (usually a different color, often blue or yellow) and several LAN ports (usually yellow or gray). The modem cable goes into the WAN port. The LAN ports are for connecting other devices like computers or printers by ethernet if you want them wired instead of wireless.
Can I connect the modem and router with WiFi instead of a cable?
No. The modem and router must be connected by ethernet cable. WiFi is only for connecting your devices (phones, laptops, tablets) to the router. The modem and router need a wired connection to each other to work reliably.
How do I know if my modem and router are actually connected?
Check the lights on the router. Look for a light labeled "Internet," "WAN," "Online," or "Connected." If this light is on and steady (not blinking), the router is receiving internet from the modem. If it is off or blinking, the connection is not working — check the cable and restart both devices.