Why you might connect router to router
Connecting a second router to your first one extends your network's reach without paying for a second internet line. This setup is useful when your main router's signal doesn't reach a far corner of your home, a garage, or a basement — places where devices disconnect or move slowly.
The second router acts as a repeater or access point, taking the signal from your main router and broadcasting it further. You control both routers from the same network, so your phone and laptop move between them without dropping the connection. The trade-off is that the second router uses some of its bandwidth to relay the signal back to the first one, so speeds in the extended area will be slower than they are near your main router.
Key Takeaways
- A second router can work in access point mode (simplest) or repeater mode (reaches further but slower), and the choice depends on where you're placing it.
- You connect the second router to the first one using an ethernet cable plugged into the main router's LAN port, not the internet port.
- The second router needs a different name (SSID) than the first one so you can tell them apart, or the same name if your router supports seamless roaming.
- You log into the second router's settings using its IP address (usually printed on the back) and turn off DHCP so it doesn't create a separate network.
- Test the connection from the far end of your home before you hide the cables, because placement matters more than settings.
Access point mode versus repeater mode
Access point mode is the simpler setup and the one most people should use. You run an ethernet cable from your main router to the second router. The second router receives the internet signal through that cable and broadcasts it wirelessly. Because it has a wired connection back to the main router, it can use its full bandwidth for the extended area. This works best if you can run a cable between the two routers — through walls, along baseboards, or through attic space.
Repeater mode uses only wireless to connect the two routers. The second router picks up your main router's signal through the air and repeats it. This is easier to set up physically because you don't need a cable, but it cuts your bandwidth roughly in half because the router is receiving and transmitting on the same frequency at the same time. Use repeater mode only if running a cable is truly impossible.
Some routers call these modes by different names — "bridge mode," "extender mode," or "mesh mode" — depending on the manufacturer. Check your router's manual or settings page to see which modes it supports.
Physical placement and cable routing
Place the second router roughly halfway between your main router and the dead zone you're trying to reach. If your main router is in the front of your house and you need coverage in the back bedroom, put the second router in the hallway or middle room. If you're extending to a garage, place it as close to the garage as possible while still being inside the house.
For access point mode, you need an ethernet cable from the main router to the second router. This cable can be as long as 100 meters (about 330 feet) without losing signal, so distance is not a constraint. Run it along baseboards, through walls using conduit, or through your attic if you have one. Avoid running it next to power lines or microwave ovens, which can cause interference.
For repeater mode, place the second router where it still gets a strong signal from the main router — usually within 30 to 50 feet and with as few walls between them as possible. The stronger the signal the second router receives, the stronger the signal it can repeat.
Connecting the routers with an ethernet cable
If you're using access point mode, plug one end of an ethernet cable into a LAN port on the back of your main router. LAN ports are usually numbered 1, 2, 3, or 4 and are separate from the port labeled "Internet," "WAN," or "Modem." Plug the other end into a LAN port on the second router — not the internet port.
Power on the second router and wait two to three minutes for it to boot up. The lights on the back should stabilize, usually showing a solid or slowly blinking light. If the lights are off or red, the cable may not be seated properly — unplug it from both ends and plug it back in firmly.
For repeater mode, you do not need a cable. Skip this step and move to the settings section.
Logging into the second router and changing its settings
Find the IP address of your second router. It's usually printed on a sticker on the back of the device, often something like 192.168.1.1 or 192.168.0.1. Open a web browser on a computer or phone connected to your main router's network and type that IP address into the address bar. You should see a login page.
Enter the username and password. These are usually "admin" and "admin," or "admin" and the router's serial number (also on the sticker). If you've changed these before, use the credentials you set. If you're locked out, look for a small reset button on the back of the router — hold it for 10 seconds to restore factory settings, which will erase any changes you've made.
Once you're logged in, look for a section called "Operating Mode," "Network Mode," or "Wireless Settings." Select "Access Point" if you're using a cable, or "Repeater" or "Extender" if you're using wireless only. Save the changes.
Naming the second router and turning off DHCP
In the same settings area, find the wireless network name (called SSID). You have two options: give it a different name than your main router, or give it the same name.
A different name is simpler to understand. You'll see two networks in your list of available WiFi networks — one from each router. Your phone or laptop will connect to whichever one has the stronger signal. This works well if you're stationary (working at a desk in the extended area) but can cause brief disconnections if you move between the two routers while on a call or video.
The same name is more seamless if your router supports it. Your devices will switch between routers automatically without dropping the connection. Check your router's manual to see if it supports "seamless roaming" or "802.11k/v/w" — if it does, use the same name and the same password on both routers.
Next, find the DHCP setting. DHCP is the system that assigns IP addresses to devices on your network. Turn it off on the second router. If you leave it on, the second router will create a separate network, and devices won't be able to see each other. Save the changes.
Testing the connection before you finish
Walk to the far end of the area you're trying to reach — the back bedroom, the garage, the patio — and check your phone or laptop. You should see the second router's network name in your list of available WiFi networks. Connect to it and open a web browser. Load a website or run a speed test to confirm the connection works.
If the connection is slow, move the second router closer to the main router or to a higher location (routers broadcast better from elevated positions). If you're using repeater mode and the signal is weak, move the second router closer to the main router so it receives a stronger signal to repeat.
Once you've confirmed the connection works, you can hide the cables and find the second router in place. If the connection doesn't work, double-check that the ethernet cable is plugged into a LAN port (not the internet port) and that DHCP is turned off on the second router.
Frequently Asked Questions
Can I use any two routers together?
Most routers can work together in access point or repeater mode, but some older or budget models have limited options. Check your second router's manual or manufacturer website to confirm it supports the mode you want to use. If it doesn't, you may need to use repeater mode even if you prefer access point mode.
Will the second router slow down my main network?
In access point mode with an ethernet cable, no — the second router has its own wired connection and doesn't compete with your main devices. In repeater mode, yes — the second router uses some of its bandwidth to relay the signal, so speeds in the extended area will be roughly half what they are near the main router.
What if I want to use a mesh system instead?
Mesh systems are designed to work together and handle roaming better than connecting two separate routers. If you're buying new equipment, a mesh system is usually easier to set up. If you already have a second router, connecting it as described here costs nothing and works well for most homes.
Do I need to change my password on the second router?
You should change the login password (the one you use to access the router's settings) to something other than the default. The WiFi password can be the same on both routers if you're using the same network name, or different if you're using different names.
Why does my device keep switching between the two routers?
If you're using different network names, your device may switch based on signal strength rather than staying connected to one router. This is normal. If it's causing problems, try giving both routers the same name and password, or manually connect to the closer router and forget the other one temporarily.