What you need before you start

Your router needs three things to connect to the internet: a modem (the device your internet service provider gave you or you rented from them), an ethernet cable, and access to your router's settings. The modem converts the signal coming into your home—whether that's cable, fiber, or DSL—into data your router can use. The router then broadcasts that connection wirelessly to your devices.

Check that you have an ethernet cable long enough to reach from your modem to your router. Most routers come with one in the box. You'll also need to know your WiFi network name and password, which are usually printed on a sticker on the back or bottom of the router, or you can create your own after setup.

Key Takeaways

  • Connect an ethernet cable from the modem's output port to the router's internet or WAN port—not to one of the regular ethernet ports.
  • Power on the modem first, wait for its lights to stabilize, then power on the router and wait two to three minutes for it to fully boot.
  • Open a web browser and go to your router's IP address (usually 192.168.1.1 or 192.168.0.1) to log in and confirm the internet connection is active.
  • Change the default WiFi password to something only you know, and turn off WPS (WiFi Protected Setup) in the router settings for better security.
  • If the router shows no internet connection after five minutes, restart both the modem and router in order: modem first, then router.

Connecting the cables in the right order

The physical connection is the first step. Locate the port on the back of your modem labeled "out," "internet," or sometimes just "ethernet." This is where the signal leaves the modem. On your router, find the port labeled "internet," "WAN," or "uplink"—this is different from the regular ethernet ports, which are usually labeled 1, 2, 3, and 4. Plug one end of the ethernet cable into the modem's output port and the other end into the router's WAN port.

Do not plug the cable into one of the numbered ethernet ports on the router. Those ports are for connecting devices like computers or printers to your network, not for receiving the internet signal from the modem. If you plug it into the wrong port, the router will not receive internet, even though the cable is connected.

Powering on in the correct sequence

Turn on the modem first and wait. Watch the lights on the front of the modem. You should see lights for power, internet connection, and read activity. Wait until these lights stop blinking rapidly and settle into a steady pattern—this usually takes 30 seconds to two minutes. The modem needs time to sync with your internet service provider's network.

Once the modem's lights are stable, plug in the router and turn it on. The router will take longer to start up than the modem—usually two to three minutes. During this time, you'll see lights blinking on the front as it boots up and detects the internet connection from the modem. Do not unplug it or move it during this startup period. Wait until the lights settle before moving to the next step.

Logging into your router to verify the connection

Open a web browser on any device connected to the router's WiFi or plugged into one of its ethernet ports. In the address bar, type the router's IP address. For most routers this is 192.168.1.1 or 192.168.0.1, but check the sticker on your router to be sure. Press Enter.

You'll be asked to log in. The default username is usually "admin" and the default password is either "admin," "password," or printed on the router's sticker. After you log in, look for a status page or dashboard. You should see a section that shows your internet connection status. If it says "connected" or shows your public IP address, the router is receiving internet from the modem correctly.

If the status page shows "no internet" or "disconnected," wait another minute and refresh the page. If it still shows no connection after five minutes total, move to the troubleshooting section below.

Changing your WiFi password and turning off WPS

While you're logged into the router, change the WiFi password from the default. Look for a section called "WiFi," "Wireless," "SSID," or "Network Settings." You'll see the network name (SSID) that appears when you search for WiFi on your phone or computer. Change the password to something at least 12 characters long that includes uppercase letters, numbers, and symbols. Write it down or save it somewhere safe.

In the same settings area, find and turn off WPS (WiFi Protected Setup). This is a feature that lets devices connect by pressing a button, but it's a security risk because it uses a weaker connection method. Disable it, then save your changes. The router may restart after you save—this is normal and takes a minute or two.

What to do if the router still shows no internet

If the router's status page still shows no connection after waiting five minutes, restart both devices in order. Unplug the modem's power cable, wait 30 seconds, and plug it back in. Wait for its lights to stabilize again. Then unplug the router, wait 30 seconds, and plug it back in. Wait another two to three minutes for the router to fully restart.

Check the status page again. If it now shows connected, the problem was likely a temporary sync issue between the modem and router. If it still shows no connection, the issue may be with the modem itself or your internet service. Contact your internet service provider and tell them the modem is not syncing with the network. They can check the signal on their end and may need to restart the service or send a technician.

Positioning your router for the best signal

Once the internet connection is confirmed, think about where the router sits. Place it in a central, elevated location—on a shelf or mounted on a wall rather than on the floor or inside a cabinet. Avoid placing it next to other electronics like microwaves, cordless phones, or baby monitors, which can interfere with the WiFi signal. Keep it away from metal objects and dense walls.

If you have a large home or multiple floors, you may find that the signal is weak in some rooms. This is normal for a single router. You can improve coverage by adding a WiFi extender or mesh system later, but start with the router in the best central location you have.

Frequently Asked Questions

What if my modem and router are in different rooms?

You can run an ethernet cable through walls, along baseboards, or through conduit to connect them across distance. The cable itself does not carry electricity, so it's safe to run near other wires. If running a cable is not practical, some routers support a wireless bridge mode that lets them connect to the modem's signal instead of a wired connection, though this reduces speed and is less reliable.

Do I need to restart my modem and router every time I turn on my computer?

No. Once they're set up and connected, leave them powered on all the time. They're designed to run continuously. Restarting them is only necessary if the internet stops working or if you're making changes to the settings.

Why does my router have so many ethernet ports if only one connects to the modem?

The WAN port (the one connected to the modem) brings internet into the router. The other ports let you connect devices like computers, printers, or game consoles directly to the router with a wired connection, which is faster and more stable than WiFi for devices that don't move around.

Can I use the same ethernet cable for the modem and for other devices?

Yes, ethernet cables are interchangeable. Any standard ethernet cable works for any connection. The cable itself doesn't care whether it's plugged into the WAN port or a regular port—it's the port on the router that determines what the connection does.

What if I don't see my router's IP address on the sticker?

Try 192.168.1.1 first, as this is the most common default. If that doesn't work, try 192.168.0.1. If neither works, restart the router and try again. You can also check your computer's network settings to see what gateway address it's using—that's usually the router's IP address.