What happens when you switch routers

When you replace your main router, your Netgear WiFi extender does not automatically find the new one. The extender remembers the old network name and password, so it will keep trying to connect to equipment that is no longer there. You need to tell the extender about your new router by resetting it and walking through the connection process again.

This takes about 10 to 15 minutes and requires you to be in the same room as the extender for part of it. You will need your new router's network name (SSID) and password before you start.

Key Takeaways

  • Your Netgear extender will not automatically connect to a new router — it still remembers the old network and needs to be reset.
  • You can reset the extender by holding the reset button for 10 seconds, or by logging into its settings page and choosing factory reset.
  • After reset, the extender broadcasts its own temporary network that you join from your phone or computer to run the setup wizard.
  • The setup wizard asks for your new router's network name and password, then connects the extender to it.
  • Once connected, move the extender to its final location — usually halfway between the router and the dead zone you want to cover.

Reset the extender to clear the old network

The extender has a small reset button on the back or bottom, usually recessed so you need a paperclip or pen to press it. Hold it down for 10 seconds while the extender is powered on. The lights will flash and go dark, then come back on. This erases all settings, including the old router's network information.

If you cannot find the reset button or prefer not to use it, you can reset through the settings page instead. Open a web browser, go to routerlogin.net, and log in with the default username and password (usually admin / admin, printed on the extender's label). Look for a Factory Reset or Restore Defaults option in the settings menu, then confirm. The extender will restart.

After reset, the extender will broadcast a temporary network with a name like "NETGEAR-EXT" or "NETGEAR_EXT_2.4" that you can see in your phone's WiFi list. This is normal and expected.

Connect your phone to the extender's temporary network

On your phone or laptop, open WiFi settings and look for the extender's temporary network name (it starts with NETGEAR). Connect to it. You will not need a password for this step — the temporary network is open.

Once connected, a setup page should open automatically in your browser. If it does not, open a browser and go to routerlogin.net or mywifiext.net. The Netgear setup wizard will load.

Run the setup wizard and enter your new router's details

The wizard will scan for nearby WiFi networks and show you a list. Find your new router's network name in the list and select it. If you do not see it, make sure your new router is powered on and broadcasting its network name (some routers have a setting to hide the name — if yours does, you may need to type the name manually).

After you select your router's network, the wizard will ask for the password. Type it exactly as it appears — passwords are case-sensitive, so "MyPassword123" is different from "mypassword123". The extender will then connect to your new router and test the connection.

The wizard may ask whether you want to use the same network name for the extender as your main router, or a different one. Using the same name means your phone will switch between the router and extender automatically as you move around. Using a different name (like "MyNetwork-Extended") means you see both networks and can choose which one to connect to. Either works — pick whichever you prefer.

Wait for the extender to finish connecting

After you enter the password, the extender will restart and connect to your new router. This takes 2 to 3 minutes. You will see a progress bar or status message. Do not unplug the extender during this time.

Once the connection is complete, the wizard will show a success message. At this point, your phone is still connected to the extender's temporary network. You can now switch your phone back to your main router's network (or the extender's permanent network if you gave it a different name).

Position the extender for best coverage

The extender works best when it is roughly halfway between your router and the area where your signal is weak. If your router is in the living room and you have poor signal in the bedroom, place the extender in a hallway or doorway between them, not in a corner or closet.

Avoid placing the extender directly against a wall, inside a cabinet, or near metal objects like filing cabinets or microwave ovens — these block the signal. Keep it at least a few feet away from the router itself. If the extender is too close to the router, it will not extend the range meaningfully.

After you move it to its final location, give it a few minutes to reconnect. Check that your phone or computer can see the network and connect to it. Run a speed test from different rooms to confirm the coverage is better than before.

Troubleshoot if the extender will not connect

If the extender connects to your new router but then disconnects after a few seconds, the most common cause is a typo in the password. Go back to the setup wizard (by connecting to the extender's temporary network again) and re-enter the password, checking each character carefully.

If the extender cannot find your router's network at all, make sure your router is powered on and its network name is not hidden. Some routers have a "broadcast SSID" setting that you need to turn on. Check your router's manual or settings page if you are unsure.

If you see the network but the extender says "connection failed" or "incorrect password," try resetting the extender again and running through the wizard a second time. Sometimes the extender's WiFi radio needs a full restart to work properly with a new router.

Frequently Asked Questions

Do I need to unplug the extender before resetting it?

No. You can press and hold the reset button while the extender is powered on. The button is designed to work that way. After you release it, the extender will restart automatically.

What if I forgot my new router's password?

You can reset the router to factory settings (check its manual for the reset button location), which will restore the default password printed on the router's label. Alternatively, if you set up the router from a phone app, you may be able to look up the password in that app's settings. If the router is still under warranty, contact the manufacturer's support line.

Can I use the extender with a mesh WiFi system instead of a traditional router?

Netgear extenders are designed for traditional routers, not mesh systems. Mesh systems (like Netgear Orbi or Eero) already cover your home without needing an extender. If you switched to a mesh system, you do not need the extender anymore.

Why does my phone keep switching between the router and extender?

If you gave the extender a different network name than your router, your phone sees two separate networks and may switch between them as you move. To fix this, run the setup wizard again and choose to use the same network name for both. Your phone will then switch automatically without you seeing two networks.

How far can the extender reach from the router?

A Netgear extender typically reaches about 50 to 100 feet from the router in open space, depending on the model and how many walls are between them. Each wall reduces the range by 10 to 20 feet. Placing it halfway between the router and your dead zone usually works better than trying to maximize distance.