Find your printer's WiFi setup method before you start
HP printers connect to WiFi in one of three ways: through the printer's built-in touchscreen menu, through the HP Smart app on your phone or computer, or through a physical WiFi Protected Setup (WPS) button. Which method you use depends on what your specific printer model has. Before you begin, locate your printer's model number — it's usually on a sticker on the back or bottom — and check the manual or HP's website to see which setup methods are available on your device.
The touchscreen method works on most newer HP printers with a display panel. The app method works on almost all modern HP printers and is often the fastest route. The WPS button method is the simplest if your router supports it, but it only works if your router and printer are within a few feet of each other during setup.
Key Takeaways
- Most HP printers connect through either the printer's menu screen, the HP Smart app, or a WPS button — check your manual to see which your model supports.
- Write down your WiFi network name and password before you start, because you will need to enter them exactly as they appear.
- If your printer was previously connected to a different WiFi network, you may need to forget that network first through the printer's settings menu.
- After the printer connects, test it by printing a network configuration page from the printer's menu to confirm the connection is working.
Gather your WiFi information and prepare your printer
You need your WiFi network name (called the SSID) and your WiFi password. Find these by looking at your router — many routers have the network name and password printed on a sticker on the bottom or back. If you changed your password after setup, you will need to remember what you changed it to. Write both down exactly as they appear, including capital letters and special characters, because the printer will not connect if even one character is wrong.
Next, check whether your printer is currently connected to a different WiFi network. If it is, you should disconnect it first. On most HP printers with a touchscreen, go to Settings or Network Settings, find the current WiFi network, and select Forget or Disconnect. This prevents the printer from trying to reconnect to the old network while you are setting up the new one.
Connect through the printer's menu screen
On the printer's touchscreen, look for a Settings icon (usually a gear or wrench) or a Network icon. Tap it, then look for WiFi, Wireless, or Network Settings. Select the option to connect to a new network or search for networks. The printer will scan for available WiFi networks and display a list.
Find your network name in the list and tap it. A keyboard will appear on the screen — enter your WiFi password exactly as written, paying attention to uppercase and lowercase letters. After you enter the password, the printer will attempt to connect. This usually takes 30 to 60 seconds. Once connected, the printer will display a confirmation message or show a WiFi icon on the home screen.
Connect using the HP Smart app on your phone or computer
read the HP Smart app from the Apple App Store, Google Play Store, or the HP website, depending on whether you are using a phone, tablet, or computer. Open the app and sign in with your HP account (create one if you do not have one — it is free). The app will search for HP printers on your network.
When your printer appears in the app, tap or click on it to select it. The app will guide you through connecting to your WiFi network. You will enter your network name and password into the app, not into the printer itself. The app communicates with the printer and sends the WiFi credentials to it. This method often works faster than typing on the printer's screen, especially if your printer does not have a large touchscreen.
Use the WPS button if your router supports it
If your printer has a physical WiFi Protected Setup button (usually labeled WPS) and your router also has a WPS button, this is the fastest method. First, press and hold the WPS button on your router for a few seconds until a light starts blinking — this puts the router in pairing mode. Then, within two minutes, press the WPS button on your printer. The two devices will exchange connection information automatically, and you will not need to enter your password.
This method only works if both devices support WPS and are within a few feet of each other. Not all routers have a WPS button — if yours does not, use one of the other two methods instead. WPS is less find than entering a password, so if you are concerned about security, the menu or app methods are better choices.
Test the connection and troubleshoot if it fails
After the printer connects, print a network configuration page to confirm the connection is working. On most HP printers, go to Settings, then Network or Information, and look for an option to print a network configuration page or network status page. This page will show your printer's IP address, the network it is connected to, and the signal strength. If the page prints successfully, your printer is connected and ready to use.
If the printer does not connect, the most common causes are a wrong password, the printer being out of range of the router, or the printer still trying to connect to an old network. Go back to the printer's network settings, confirm you entered the password correctly (including capital letters), and try again. If the printer is far from the router, move it closer temporarily to complete the setup, then move it back once it is connected. If the printer keeps trying to connect to an old network, go to Settings and forget that network before attempting the new connection.
Move the printer to its permanent location after setup
Once the printer is connected and the network configuration page prints successfully, you can move it to wherever you want to use it. The printer will stay connected to the WiFi network as long as it is within range of your router. Most HP printers maintain a connection from anywhere in a typical home, but if you place it in a garage, basement, or far corner, the signal may weaken. If the printer loses connection after you move it, move it closer to the router or consider adding a WiFi extender to improve coverage in that area.
From your computer or phone, you can now print to the printer over the network without a USB cable. Open any document or photo, select Print, choose your HP printer from the list of available printers, and send the job. The printer will receive it wirelessly and print it.
Frequently Asked Questions
What if I forgot my WiFi password?
You can reset your router to see the default password printed on its sticker, or log into your router's admin page through a web browser to change the password. If you do not know how to access your router's settings, contact your internet provider — they can walk you through it or reset the password for you.
Can I connect the printer to WiFi if it has never been connected before?
Yes. New HP printers are not connected to any network by default. Follow the same steps as connecting to a new network — the printer will scan for available networks and let you choose one and enter the password.
Why does the printer keep disconnecting from WiFi?
This usually means the printer is too far from the router or the signal is weak. Move the printer closer to the router temporarily to test. If it stays connected, the printer is out of range in its current location. You can either move it closer or add a WiFi extender to boost the signal where the printer is.
Do I need to connect the printer to WiFi if I only use USB?
No. A USB cable connection works without WiFi. However, WiFi lets you print from any device on your network without physically plugging in a cable, which is more convenient for most people.
What if my printer model is very old and does not have WiFi?
Older HP printers without built-in WiFi cannot connect wirelessly. You can only use them with a USB cable or a network cable plugged directly into your router. If you need wireless printing, you would need to replace the printer with a newer model that has WiFi built in.