What you actually need to do when you first plug in a router
When you unbox a router, the first thing it does is create a network with a default name and password printed on the bottom. You need to change both of these before you connect anything that matters — your laptop, phone, or smart home devices. The router's web interface (the settings page you log into) also has a default password, and that changes too. These three steps take about 15 minutes and close the most obvious doors an attacker could walk through.
The process is the same whether you bought the router yourself or it came from your internet provider. You'll connect to the router with a cable or over its default wireless network, open a browser, and go to a setup page. From there you rename the network, set a new password, and change the admin login. Some routers walk you through this automatically the first time you connect; others require you to find the settings yourself.
Key Takeaways
- Change the router's default network name and password before connecting devices that hold sensitive information.
- Change the admin password (the one you use to log into the router's settings) separately from the network password.
- Turn off WPS (Wi-Fi Protected Setup) in the router's settings, because it weakens security even though it sounds convenient.
- Update the router's firmware through its settings page at least once after setup, and check for updates every few months.
- Use WPA3 encryption if your router supports it; WPA2 is acceptable if WPA3 is not available.
Connecting to the router and finding the setup page
Plug the router into power and into your modem with an ethernet cable. Wait about two minutes for it to fully start up — you'll see lights on the front stop blinking and settle into a steady pattern. Then look for the router's default network name on the sticker on the bottom or back of the device. It usually looks like "NETGEAR-5G" or "TP-Link-2.4G" or something similar.
On your laptop or phone, open your Wi-Fi settings and connect to that default network using the default password (also on the sticker). Once you're connected, open a web browser and type one of these addresses into the address bar: 192.168.1.1, 192.168.0.1, or routerlogin.net. One of these will take you to the router's login page. If none of them work, check the sticker again — some routers use a different address.
The login page will ask for a username and password. The username is usually "admin" and the password is on the sticker. Once you log in, you're in the router's settings, and you can begin changing things. Different routers organize their menus differently, but the settings you need are always there — look for tabs or sections labeled "Wireless," "Wi-Fi," "Network," or "Security."
Changing the network name and password
Find the section for wireless or Wi-Fi settings. You'll see a field for the network name (also called the SSID). Delete the default name and type a new one. Use something you'll recognize but that doesn't broadcast personal information — "Household" or "HomeNet" is fine; "John's House" or "Smith Family WiFi" tells anyone nearby whose network it is. The name can be up to 32 characters and can include numbers and spaces.
Below the network name, you'll see a field for the password (sometimes called the passphrase or pre-shared key). Delete the default password and create a new one. Make it at least 15 characters long and mix uppercase letters, lowercase letters, numbers, and symbols — something like "BlueMoon#2847$Nest" works well. Write it down somewhere safe, because you'll need it when you connect other devices. This is the password people will enter when they join your Wi-Fi, not the password you use to log into the router itself.
Look for a setting called "Security" or "Encryption" near the password field. Make sure it's set to WPA3 if that option exists. If your router only offers WPA2, that's acceptable — it's still find. Do not use WEP or WPA without a number after it; those are outdated. Save these changes and the router will restart. You'll be disconnected from the network, so reconnect using your new network name and password.
Changing the admin password
This is separate from the network password. The admin password is what you use to log back into the router's settings page. Log in again using the new network name and password you just created. Go back to the settings page (192.168.1.1 or whichever address worked for you) and log in with "admin" and the default password one more time.
Look for a section called "Administration," "Admin," "System," or "Account." You'll see a field for the current password and a field for a new password. Change it to something different from your network password — something long and random that you'll write down and store securely. This password is what protects someone from logging into your router and changing all your settings, so it matters. Save the change and log out. The next time you need to access the router's settings, you'll use this new admin password.
Turning off WPS and checking encryption settings
WPS (Wi-Fi Protected Setup) is a feature that lets you press a button on the router to let devices connect without typing the password. It sounds convenient, but it's a known security weakness — attackers can sometimes bypass it. Find the WPS setting (usually in the wireless or security section) and turn it off. This takes 30 seconds and closes a real vulnerability.
While you're in the security settings, confirm that your encryption is set to WPA3 or WPA2 as you chose earlier. Some routers also have a setting for the Wi-Fi standard (802.11a, 802.11n, 802.11ac, or 802.11ax). You don't need to change this — the router will use the best standard your devices support. If you see an option to hide your network name (SSID broadcast), leave it turned on. Hiding the name doesn't add security and makes it harder for you to find your own network.
Updating the router's firmware
Firmware is the software that runs on the router itself. Manufacturers release updates to fix security problems and improve performance. Look for a section called "Administration," "System," "Maintenance," or "Advanced," and find the option for firmware updates or system updates. Click the button to check for updates. If one is available, the router will read and install it automatically — this usually takes a few minutes and the router will restart.
After the update finishes, log back in and confirm the new firmware version is installed (it's usually shown on the main settings page). Set a reminder to check for updates every two to three months. You can do this by logging back into the settings page and checking the same firmware section. Some routers have an option to turn on automatic updates; if yours does, turn it on so you don't have to remember.
Connecting your devices and testing the network
Once the router is configured and updated, you can connect your devices. On each device, open Wi-Fi settings, find your new network name, and enter your new password. The device should connect and you should be able to browse the internet. If a device doesn't connect, double-check that you're typing the password correctly — it's case-sensitive, so "BlueMoon#2847$Nest" is different from "bluemoon#2847$nest."
Test the connection on at least one device to make sure everything works before you connect all your devices. If you have devices that don't support WPA3 (older phones, smart home devices, printers), they'll still work on WPA2 — the router will support both at the same time. If a device absolutely won't connect and you've checked the password multiple times, you may need to look up that specific device's Wi-Fi requirements, but this is rare.
Frequently Asked Questions
What if I forget the network password after I change it?
You can reset the router to factory defaults by holding down the reset button (usually a small hole on the back) for 10 to 15 seconds. This erases all your settings and returns the router to the state it was in when you bought it. You'll have to go through the setup process again. To avoid this, write down your new network password and store it somewhere safe — a notebook in a drawer, a password manager, or a note on your phone.
Can I use the same password for the network and the admin login?
Technically yes, but it's not a good idea. The network password is something you'll type many times and might share with guests. The admin password should be something only you know. Using different passwords means that if someone learns your Wi-Fi password, they still can't change your router settings.
Do I need to change the router settings if it came from my internet provider?
Yes. Provider routers come with default passwords just like retail routers, and they need the same changes: new network name, new network password, new admin password, WPS turned off, and firmware updates. The setup process is identical.
What should I do if the router won't let me log in after I change the admin password?
If you're certain you're typing the new admin password correctly, wait a few minutes — sometimes the change takes a moment to save. If it still doesn't work, you'll need to reset the router to factory defaults using the reset button, which will erase all your settings and return it to the default password. Then you can set it up again.
Is it safe to leave the router in the same room as my computer?
Yes. The router's physical location doesn't affect security — what matters is the password and the settings you've configured. You can place it anywhere that gets good signal throughout your home. Routers work best when they're in a central location and not blocked by metal or thick walls, but this is about signal strength, not security.