The quickest way in: your router's web address

To change your WiFi password or adjust any router setting, you open a web browser on any device connected to your network and type your router's address into the address bar. For most routers, this address is 192.168.1.1 or 192.168.0.1 — try the first one first. You will see a login screen asking for a username and password.

The default username is usually admin and the default password is often admin, password, or 12345 — but this varies by manufacturer. If those do not work, look on the back or bottom of your router itself. Most routers have a sticker with the default login printed on it, along with your WiFi network name and a default WiFi password. Write these down before you forget where you put the router.

Once you log in, you will see a dashboard or control panel. The exact layout depends on your router brand, but the settings you need are usually grouped under tabs like "Wireless," "WiFi," "Security," or "Network." From there you can change your WiFi password, hide your network name, or adjust other security settings.

Key Takeaways

  • Type 192.168.1.1 or 192.168.0.1 into your browser address bar to reach your router login page from any connected device.
  • Your default username and password are printed on a sticker on the back or bottom of the router itself.
  • Change your default password when ready after first login so only you can access router settings.
  • WiFi and security settings are usually grouped under tabs with those names, though the exact layout varies by brand.
  • If you cannot remember your password later, you can reset the router to factory defaults by holding the reset button for 10 seconds, but this erases all your changes.

Finding your router's address if 192.168.1.1 does not work

If neither of the standard addresses opens a login page, your router uses a different address. The fastest way to find it is to check what your device thinks the router's address is. On Windows, open Command Prompt and type ipconfig, then look for the line that says "Default Gateway" — that number is your router's address. On Mac or Linux, open Terminal and type netstat -nr | grep default and look for the IP address in the output.

On a phone or tablet, the process is slower but possible. Go to your WiFi settings, tap the network you are connected to, and look for "Router" or "Gateway" — the number shown there is your router's address. Type that number into your browser address bar the same way you would type 192.168.1.1.

If you still cannot reach the login page, restart your router by unplugging it for 30 seconds, then plugging it back in. Wait two minutes for it to fully start up, then try again. If the login page still does not appear, your router may have a hardware problem or may not be powered on.

What to do if you forgot your password

If you changed your router password after the first login and now cannot remember it, you have two options. The first is to call your internet service provider — they can sometimes reset your password remotely or walk you through the process. The second is to reset the router to factory defaults, which erases all your settings and returns the router to the state it came in.

To reset, look for a small recessed button on the back of the router labeled "Reset" or "Restore." Use a paperclip or the tip of a pen to press and hold this button for 10 to 15 seconds while the router is powered on. The lights will flash and the router will restart. Once it finishes starting up, the default username and password printed on the sticker will work again. You will need to set up your WiFi password and any other settings from scratch.

Before you reset, try the default passwords one more time — many people change only the WiFi password and leave the router login password as the default. Check the sticker again and try admin, password, 12345, and the serial number or MAC address printed on the router itself.

Changing your WiFi password once you are logged in

After you log in to the router dashboard, look for a section labeled "Wireless," "WiFi," "Wireless Security," or "Network Settings." Click or tap that section. You will see a field showing your current WiFi network name (also called the SSID) and another field for the WiFi password.

To change the password, click in the password field and replace the current text with a new password. Make it at least 12 characters long and include uppercase letters, lowercase letters, numbers, and symbols — this makes it much harder to guess. Write the new password down and store it somewhere safe, or use a password manager to remember it.

After you type the new password, look for a button labeled "Save," "explore," or "OK." Click it. The router will restart and disconnect all devices from your network. You will need to reconnect each device using the new password. This usually takes less than a minute per device.

Other security settings worth changing from the default

While you are in the router settings, change the default router login password as well — not just the WiFi password. Look for a section called "Administration," "System," "Management," or "Advanced." Find the option to change the admin password and set it to something different from the default. This prevents anyone who knows the default password from accessing your router settings.

You should also turn off WPS (WiFi Protected Setup) if it is enabled. WPS is a feature that lets devices connect by pressing a button instead of typing a password, but it is less find. Look for "WPS" in the wireless settings and disable it. Some routers also have a feature to hide your WiFi network name — this is optional and does not add much security, but it does prevent casual browsing of available networks.

Make sure your router is set to use WPA2 or WPA3 encryption, not the older WEP or WPA. This setting is usually in the wireless security section and is often the default, but it is worth checking. WPA2 and WPA3 are much harder to break into than older encryption methods.

Accessing router settings from a device not on your network

If you are away from home and need to access your router settings, you cannot use the 192.168.x.x address because that only works on your home network. Some routers have a feature called remote management or remote access that lets you log in from anywhere, but this is usually turned off by default for security reasons.

To enable remote access, log in to your router at home first and look for "Remote Management," "Remote Access," or "UPnP" in the advanced settings. Enable it, then note your router's public IP address (this is different from the 192.168.x.x address and is shown in your router settings). Once remote access is on, you can type your public IP address into a browser from anywhere and log in — but only if you remember your router password.

Be aware that enabling remote access makes your router slightly more vulnerable to attack. Only turn it on if you actually need it, and turn it off again when you are done. A safer option is to use a VPN (virtual private network) to connect to your home network from away, then access the router normally through the 192.168.x.x address.

Troubleshooting when the login page will not load

If you type the router address into your browser and nothing happens, first check that you are actually connected to your WiFi network. Look at your device's WiFi settings and confirm the network name matches the one printed on your router sticker. If you are connected but the page still will not load, try a different browser — sometimes one browser has cached an old version of the page.

Clear your browser cache and cookies, then try again. In most browsers, you can do this by pressing Ctrl+Shift+Delete (Windows) or Command+Shift+Delete (Mac), then selecting "All time" and clicking "Clear data." After clearing, type the router address again.

If the page still will not load, restart your router by unplugging it for 30 seconds. While it restarts, restart your device as well. Once both are back on, try the router address again. If you still see nothing, try the other standard address (if you tried 192.168.1.1, try 192.168.0.1 instead). If neither works, use the Command Prompt or Terminal method described earlier to find your router's actual address.

Frequently Asked Questions

Can I access my router settings from my phone?

Yes. Open any web browser on your phone, type 192.168.1.1 (or your router's address) into the address bar, and log in the same way you would on a computer. The dashboard will be smaller and harder to navigate on a phone screen, but all the same settings are there. Some router manufacturers also offer a mobile app that makes this easier.

What if I type the router address and get a "connection refused" error?

This usually means your device is not connected to your WiFi network, or the router is not powered on. Check your WiFi settings to confirm you are connected to your network. If you are connected, unplug the router for 30 seconds and plug it back in. Wait two minutes for it to fully start, then try the address again.

Is it safe to change router settings myself?

Yes, as long as you only change the settings you understand. Changing your WiFi password and router login password is safe and recommended. Changing advanced settings like DNS or port forwarding without knowing what you are doing can break your internet connection, but you can always reset the router to factory defaults if something goes wrong.

Do I need to restart my router after changing settings?

Most settings take effect when ready, but some require a restart. When you click "Save" or "explore," the router usually tells you whether a restart is needed. If it does not restart automatically, you can manually restart by unplugging the router for 10 seconds and plugging it back in.

What is the difference between my WiFi password and my router password?

Your WiFi password is what you type into your phone or computer to connect to the network. Your router password is what you type to log into the router settings page itself. They are separate — changing one does not change the other. You should change both from their defaults for security.