Export water through the water management menu, not through a separate export tool

Cities: Skylines 2 does not have a dedicated water export feature like it does for other resources. Instead, you manage water flow and distribution through the water management overlay and pipe connections. If you want to move water from one part of your city to another or send excess water outside your city boundaries, you do this by building water pipes that connect to the edge of the map or to other districts.

The confusion often comes from players expecting an export menu similar to electricity or goods trading. Water in Cities: Skylines 2 works differently — it flows through your pipe network based on pressure and elevation, and you control where it goes by deciding where to place pipes and pumping stations.

Key Takeaways

  • Water moves through pipes based on gravity and pressure, so place pipes from high-elevation water sources toward lower areas or the map edge to export it.
  • Use water pumping stations to move water uphill or to create pressure in your pipe network when gravity alone is not enough.
  • The water management overlay shows water flow direction and pressure levels, helping you see where water is actually moving.
  • To export water outside your city, run pipes to the map boundary and they will automatically connect to the outside region.
  • Excess water that has nowhere to go will back up in your pipes and cause pressure problems, so plan your pipe routes before building.

Understanding water flow and pressure in your pipe network

Water in Cities: Skylines 2 flows downhill naturally due to gravity. If you have a water source at elevation 100 and pipes running downhill to elevation 50, water will flow in that direction without any pump. This is the simplest way to move water across your city or toward the map edge.

Pressure is what keeps water moving. When water has nowhere to go — when pipes are blocked, full, or lead to a dead end — pressure builds up and can cause pipes to back up or burst. You can see pressure levels in the water management overlay by toggling it on in the view options menu. Green indicates healthy pressure, yellow means moderate pressure, and red means dangerous pressure that needs when ready attention.

If you need to move water uphill or maintain flow in a flat area, you must use a water pumping station. Place a pumping station in your pipe network and it will actively push water in the direction you want it to go, overriding gravity. Pumping stations consume electricity, so they add to your power demand.

Setting up pipes to export water to the map edge

To export water outside your city, run a water pipe from your treatment plant or water source toward the edge of the map. The pipe does not need to reach exactly to the boundary — when a pipe gets close enough to the map edge, it automatically connects to the outside region and water flows out.

Plan your pipe route before you build. Trace a path from your water source downhill toward the map edge if possible, as this requires no pumping stations and no electricity. If your water source is uphill from the map edge, gravity will do the work for you. If your source is lower than the edge, you will need pumping stations along the route.

Check the water management overlay while you are building to confirm water is actually flowing in the direction you intend. If the pipes show no flow or reverse flow, adjust your route or add a pumping station to create the pressure you need.

Using the water management overlay to see flow direction

Open the view options menu and toggle on the water management overlay. This shows your entire pipe network with color coding for flow and pressure. Pipes with active water flow appear in blue, while pipes with no flow appear gray or faded.

The overlay also displays small arrows on pipes showing the direction water is moving. If arrows point the wrong way, you have a pressure or gravity problem. Adjust your pipe layout or add a pumping station upstream to reverse the flow.

Use the overlay while testing your export setup. Build a small section of pipe from your water source toward the map edge, turn on the overlay, and watch whether water actually flows. This prevents you from building a long pipe network only to discover later that water is not moving the way you expected.

Handling excess water and preventing pipe backups

If water has nowhere to go, it backs up in your pipes and creates pressure problems. Excess water from treatment plants, rain runoff, or natural sources must flow somewhere — either to another part of your city, to a water storage tank, or out of the map entirely.

Water storage tanks hold water temporarily and release it slowly when demand is high. If you have seasonal flooding or uneven water demand, tanks can absorb excess water during high-flow periods and release it later. Place tanks in your pipe network between your source and your export route.

If you are still seeing pressure warnings after adding storage, you need more export capacity. Build additional pipes to the map edge, add more pumping stations to increase flow rate, or reduce the amount of water entering your system by adjusting water source placement or treatment plant output.

Connecting water sources to export routes efficiently

Start with your water source — either a water pump drawing from the water table, a treatment plant processing sewage, or a natural water feature. From there, run pipes downhill toward your export point at the map edge. Every bend and elevation change affects flow, so the more direct your route, the less pressure loss you experience.

If your city layout forces you to take a long or winding route, add pumping stations at intervals to maintain pressure. A pumping station every 10 to 15 tiles of pipe is a reasonable starting point, though you can adjust based on what the overlay shows.

Test your route with a small section first. Build 5 to 10 tiles of pipe, check the overlay to confirm flow, then extend it. This approach catches problems early before you have invested in a full network that does not work.

Common mistakes that block water export

The most common mistake is building pipes that do not actually connect to anything. Pipes must form a continuous path from source to destination. If you have a gap, water cannot flow. Check your pipe connections carefully — pipes snap to each other when placed correctly, and the overlay will show no flow if there is a break.

Another frequent problem is placing the export pipe at the wrong elevation. If your export pipe is higher than your water source, gravity works against you and you need a very powerful pumping station. Reverse the route if possible, or accept that you will need multiple pumps and extra electricity cost.

Forgetting to toggle on the water management overlay before building is also common. Many players build an entire pipe network, turn on the overlay, and discover water is flowing backward or not at all. Always use the overlay while building to see results in real time.

Frequently Asked Questions

Can I export water to another city or region?

Water pipes that reach the map boundary automatically connect to the outside region. You cannot control where that water goes or receive payment for it — it straightforward leaves your city. If you want to trade water with another city, Cities: Skylines 2 does not currently support that mechanic.

Do I need a water treatment plant to export water?

No. You can export raw water directly from a water pump or natural water source. However, exporting untreated water may cause problems in the outside region, and some players prefer to treat water before export for realism. Treatment plants also allow you to process sewage into usable water.

What happens if my export pipes are full and water cannot leave?

Water backs up in your pipes, creating dangerous pressure. Pressure warnings appear on affected pipes, and eventually pipes can burst or stop flowing entirely. Add more export pipes to the map edge, increase pumping capacity, or reduce water input to your system.

How do I know if my water export is actually working?

Turn on the water management overlay and look for blue pipes with arrows pointing toward the map edge. If pipes are gray or show no arrows, water is not flowing. Check for elevation problems, broken connections, or pressure issues blocking the flow.

Can I export water uphill to the map edge?

Yes, but you need pumping stations to push water uphill against gravity. Place pumps along your pipe route at regular intervals. Each pump consumes electricity, so exporting uphill costs more than exporting downhill.