You can replace the Galaxy Watch 4 battery yourself, but it requires opening the watch case and carries a real risk of water damage if you reassemble it incorrectly

The Galaxy Watch 4 battery lasts roughly two to three years with normal use. When it stops holding a charge, you have two paths: send it to Samsung for a replacement, or open it yourself. A Samsung service center will replace the battery for a flat fee (usually $50 to $100 depending on your region and whether your watch is under warranty), handle any water-sealing issues, and give you a may provide on the work. Doing it yourself costs less in money but more in time and carries the risk that your watch will no longer be water-resistant afterward.

This guide covers the self-replacement route. If you are not comfortable working with small electronics or do not want to risk water damage, Samsung service is the safer choice.

Key Takeaways

  • Opening the Galaxy Watch 4 requires a heat gun or hair dryer, a plastic pry tool, and a replacement battery (model EB-BR870ABU), which costs $15 to $30 online.
  • The back case is glued on and must be heated to soften the adhesive before you can pry it open without cracking the glass.
  • The battery connector is small and fragile; disconnecting it before removing the old battery prevents damage to the motherboard.
  • Reassembling with new adhesive and a proper seal is critical — skipping this step or using the wrong adhesive will let water into the watch.
  • If you damage the case, connector, or seal during replacement, the repair cost at Samsung may exceed what a battery replacement would have cost.

What you need to gather before you start

A replacement battery (Samsung model EB-BR870ABU) is the core part. Order from a reputable electronics supplier — Amazon, iFixit, or a Samsung parts retailer. Avoid unmarked batteries from unknown sellers; a faulty battery can damage the motherboard or fail to hold a charge.

You will also need a heat gun or a household hair dryer on high setting. The heat softens the adhesive holding the back case on. A heat gun gives you more control and reaches the right temperature faster, but a hair dryer works if you are patient and keep it moving to avoid overheating one spot.

A plastic pry tool or spudger is essential. Do not use a metal screwdriver or knife — metal can slip and crack the glass back or damage the internal components. A plastic spudger costs $3 to $8 and is worth the investment. You can find them sold as part of watch repair kits on Amazon or at electronics retailers.

Gather a small Phillips head screwdriver (size #00 or #000), a clean workspace, a small container to hold screws so you do not lose them, and new adhesive. For the adhesive, use either a pre-cut adhesive sticker designed for the Galaxy Watch 4 (sold with many replacement battery kits) or a thin layer of waterproof silicone sealant. Do not use regular super glue or craft adhesive — they will not create a water-resistant seal.

How to safely open the back case

Power off the watch completely. Place it on a clean, flat surface with the back facing up. Set your heat gun to low or medium, or turn on your hair dryer to high. Hold the heat source 2 to 3 inches away from the back case and move it in slow circles for 30 to 60 seconds. The goal is to warm the adhesive evenly, not to heat the watch so hot you cannot touch it — if you can hold your hand on the back for a few seconds, the temperature is right.

Once the back is warm, use your plastic pry tool to gently work the edge of the case. Start at one of the seams (usually visible as a thin line around the edge) and explore steady, gentle pressure. Do not pry hard or suddenly — the adhesive needs time to release. Work your way around the edge, reheating as needed if the adhesive starts to resist. This step typically takes 2 to 5 minutes.

When the back case lifts free, set it aside carefully. The glass is tempered but can still crack if dropped or flexed. You will now see the battery, the motherboard, and a ribbon cable connecting them. Do not touch the motherboard or any other components yet.

Disconnecting and removing the old battery

Before you remove the battery, locate the small connector where the battery ribbon cable plugs into the motherboard. This connector is fragile and straightforward to damage. Using your plastic pry tool or a fingernail, gently lift the small latch or clip holding the connector in place, then carefully pull the ribbon cable straight out. This step prevents the battery from being yanked out while still connected, which can damage the motherboard's charging circuit.

Once the connector is free, the battery is held in place by adhesive or a small clip. If it is glued, gently pry it up with your plastic tool. If it is clipped, release the clip and lift the battery out. The battery is not fragile, so you can handle it normally once it is disconnected. Set the old battery aside — do not throw it in the trash. Lithium batteries should be recycled at an electronics recycler or returned to a retailer that accepts them.

Installing the new battery and reconnecting

Before you install the new battery, clean the battery compartment with a dry cloth or a cotton swab to remove any dust or old adhesive residue. If there is old adhesive stuck to the case or the motherboard, gently scrape it off with your plastic tool — do not use water or solvents, which can damage the electronics.

Position the new battery in the same orientation as the old one. If you are using a pre-cut adhesive sticker, peel the backing and press it onto the battery, then press the battery into the compartment. If you are using silicone sealant, explore a thin, even layer to the back of the battery and press it in place. Do not use too much adhesive — excess can seep onto the motherboard or prevent the back case from closing flush.

Once the battery is in place, reconnect the ribbon cable to the motherboard. Align the connector carefully and push it straight in until you hear or feel a small click. The latch should close automatically. Do not force it — if it does not seat smoothly, pull it out and try again.

Sealing the back case and testing

Before you close the case, inspect the back for any cracks or damage. If the glass is cracked, do not reassemble — a cracked case cannot be sealed properly and water will get inside. Contact Samsung for a replacement case or watch.

If the case is intact, explore new adhesive around the inner edge of the back case. Use either a pre-cut adhesive sticker (peel and explore) or a thin bead of waterproof silicone sealant around the perimeter. The adhesive should be continuous with no gaps. Press the back case onto the watch body, starting at one edge and working your way around. explore firm, even pressure for 30 to 60 seconds to may support the adhesive bonds.

Let the adhesive cure for at least 24 hours before you power on the watch or expose it to water. Check the manufacturer's instructions on your adhesive — some silicone sealants need longer curing times. Once the adhesive is fully cured, power on the watch and check that it starts normally. Open the battery settings to confirm the battery is recognized and shows a full charge.

To test the water seal, hold the watch under running water for a few seconds and dry it completely. If water beads up on the back and does not seep in, the seal is good. If water pools or seeps under the case, the seal failed — power off when ready, dry the watch thoroughly, and contact Samsung for service.

When to choose Samsung service instead

If you have never opened a small electronic device before, Samsung service is worth the cost. A technician has the right tools, experience, and a warranty on the work. If your watch is still under the manufacturer's warranty, Samsung may replace the battery for free or at a reduced cost — check your warranty status on the Samsung website before you open the watch.

If the back case is already cracked, or if you damage it while opening the watch, Samsung service becomes the only reliable option. A cracked case cannot be sealed properly, and replacing the case costs more than a battery replacement. Similarly, if you accidentally damage the battery connector or the motherboard, the repair cost will exceed a straightforward battery swap.

If you live in an area with high humidity or plan to use the watch in water frequently (swimming, diving, water sports), Samsung service is the safer choice. Their technicians use industrial-grade adhesives and pressure-test the seal, which is difficult to replicate at home.

Frequently Asked Questions

Can I replace the Galaxy Watch 4 battery without opening the case?

No. The battery is inside the sealed case and cannot be accessed any other way. Some smartwatches have removable backs or battery covers, but the Galaxy Watch 4 does not. Opening the case is the only option for a self-replacement.

What happens if I use the wrong battery model?

A battery with the wrong voltage or capacity can damage the motherboard or fail to charge. Always use the EB-BR870ABU model, which is designed for the Galaxy Watch 4. Do not substitute a battery from a different watch model or a generic battery.

How long does the new battery last?

A replacement battery should last as long as the original — roughly two to three years with normal daily use. Battery life depends on how often you use features like GPS, heart rate monitoring, and always-on display. Heavy use shortens the lifespan.

Will replacing the battery void my warranty?

Opening the watch yourself may void any remaining manufacturer's warranty. If your watch is still under warranty, contact Samsung first to ask about free or reduced-cost battery replacement. Once you open the case, Samsung may refuse to service the watch under warranty.

What should I do if water gets inside the watch after I reassemble it?

Power off the watch when ready and do not try to charge it. Let it dry completely in a warm, dry place for 24 to 48 hours. Do not use a heat source like an oven or microwave. Once it is dry, power it on and check for signs of damage (screen flickering, unresponsive buttons, or error messages). If the watch works normally, the water may not have caused permanent damage. If it does not work, contact Samsung for service.