What you need before you start
A Nest Learning Thermostat installs in place of your existing thermostat, so the first step is checking whether your heating and cooling system will work with it. Nest requires a C-wire — a common wire that provides continuous power — or a compatible power adapter. If your current thermostat has wires running to it, you almost certainly have the wires you need; the question is whether one of them is the C-wire.
Before you touch anything, turn off power to your heating system at the breaker. Take a photo of your current thermostat's wiring with your phone, then take a picture of the breaker you switched off. This matters because if something goes wrong, you need to know exactly what you started with and which breaker controls the system.
Gather these items: a screwdriver (usually Phillips head), the Nest thermostat box itself, your phone or a computer to set it up later, and the label stickers that come in the box. You do not need a electrician for most homes, but if your system uses more than six wires, or if you have a heat pump with auxiliary heat, read the Nest compatibility checker on Google's website first — some setups need professional installation.
Key Takeaways
- Turn off power at the breaker before removing your old thermostat, and photograph the wiring so you can match it to the Nest terminals.
- The Nest thermostat has labeled terminals on the back; each wire from your old thermostat connects to the terminal with the same letter.
- If you do not have a C-wire, the Nest Power Connector (included) can provide power through your furnace, but it requires an extra step during installation.
- After wiring is complete, turn power back on, and the Nest will guide you through setup on your phone or computer.
- If your heating or cooling does not turn on after setup, the most common cause is a wire in the wrong terminal — check your photo against the Nest terminals.
Remove the old thermostat and label the wires
With power off at the breaker, unscrew the faceplate of your old thermostat and pull it away from the wall. You will see wires connected to terminals labeled with letters or colors. Using the label stickers from the Nest box, stick one label next to each wire and write the letter or color of the terminal it is connected to. For example, if a red wire connects to the terminal marked R, write "R" on the label next to that wire.
Once every wire is labeled, unscrew each wire from its terminal. Keep the wires in a bundle so they do not fall back into the wall — you can tape them to the wall with painter's tape if needed. Remove the old thermostat's base plate from the wall by unscrewing it. You now have access to the hole in the wall where the wires come through.
Before you go further, look at the wires coming through the wall. Count them. If there are more than six wires, or if you see wires labeled with letters you do not recognize, stop and check the Nest compatibility page. If you have exactly six or fewer wires and they match common labels (R, W, Y, G, C, O/B), you can proceed.
Install the Nest base plate and prepare for wiring
The Nest base plate is the part that screws to the wall. Align it over the hole where your old thermostat was, and use the screws provided to attach it. Make sure it is level — use a level tool if you have one, or just eyeball it against the wall trim. The base plate has a small opening at the bottom where the wires will pass through.
Feed the wires through the opening in the base plate. Pull them through gently so they have enough slack to reach the terminals on the back of the Nest unit itself. The terminals are on the back of the Nest and are labeled with letters: R, W, Y, G, C, O/B, and a few others depending on your system. Look at your photo of the old thermostat and match each wire to the same letter on the Nest base plate.
If you have a C-wire — a wire labeled C that you photographed from your old thermostat — you are ready to connect wires. If you do not see a C-wire in your photo, you will need to use the Nest Power Connector, which comes in the box. Set that aside for now; you will install it after the other wires are connected.
Connect the wires to the Nest terminals
Strip about one-quarter inch of insulation from the end of each wire using a wire stripper, or carefully with a utility knife. You need just enough bare wire to fit into the terminal. Loosen the terminal screw on the Nest base plate that matches your first wire's letter. Insert the bare wire into the terminal opening and tighten the screw firmly — it should not pull out if you tug gently on the wire.
Repeat this for every wire, matching the letter on your label to the letter on the Nest terminal. The most common wires are R (power from the furnace), W (heat), Y (cooling), and G (fan). If you have an O or B wire, it goes to the O/B terminal. Work slowly and double-check each connection against your photo before moving to the next wire.
Once all wires are connected, gently push the bundle of wires back into the wall opening so they do not stick out. The Nest unit itself will mount on top of the base plate, so you want the wires tucked away neatly. If any wire feels loose, tighten its terminal screw again.
Install the Power Connector if you do not have a C-wire
If your old thermostat had no C-wire, the Nest Power Connector lets the thermostat draw power from your furnace instead. The Power Connector is a small box that comes in the Nest package. It connects to two terminals on your furnace control board — usually labeled C and R, or sometimes labeled differently depending on your furnace model.
Turn off power again at the breaker. Locate your furnace in the basement or utility closet and find the control board — it is the circuit board with small terminal screws. Consult the Nest installation guide that came in the box for the exact terminals on your specific furnace model, as they vary. Connect the two wires from the Power Connector to those terminals, then turn power back on.
The Power Connector sits inside your furnace, so you do not need to hide it or mount it anywhere special. Once it is wired, the Nest thermostat will have the continuous power it needs through the C terminal on the base plate, even though you do not have a physical C-wire running from the furnace to the thermostat.
Mount the Nest unit and turn power back on
With all wires connected to the base plate, slide the Nest unit onto the base plate. It should click or snap into place. The unit will not power on until you restore power at the breaker. Go back to the breaker panel and switch the heating system breaker back to the on position.
The Nest screen should light up within a few seconds. If it does not, turn the breaker off again, wait 30 seconds, and turn it back on. If the screen still does not light, check that every wire is fully inserted into its terminal and that the terminal screw is tight. A loose connection is the most common reason the Nest does not power on.
Once the screen is on, the Nest will walk you through setup. You will need your Wi-Fi network name and password, and you will create a Google account or sign in to an existing one. The Nest will ask you what type of heating and cooling system you have — answer honestly, because this tells the Nest which wires control which functions.
Test your heating and cooling after setup
After setup is complete, test both heating and cooling to make sure they work. Set the Nest to heat mode and raise the temperature above the current room temperature. You should hear your furnace kick on within a minute. If it does not, turn off the Nest, go back to the breaker, and check that the W wire is firmly connected to the W terminal on the base plate.
Next, set the Nest to cooling mode and lower the temperature below the current room temperature. Your air conditioning should turn on. If it does not, check that the Y wire is firmly in the Y terminal. If both heating and cooling work, your installation is complete.
If one system works but the other does not, the problem is almost always a wire in the wrong terminal. Turn off power, check your original photo, and move the wire to the correct terminal. Turn power back on and test again. Do this one wire at a time so you know which one fixed the problem.
Frequently Asked Questions
What if I cannot find a C-wire in my old thermostat?
Look at all the wires again. The C-wire is usually blue or black, but color is not reliable — go by the terminal letter instead. If your old thermostat truly has no C terminal, you will use the Nest Power Connector, which connects inside your furnace instead. This is a normal setup and works just as well as having a C-wire run to the thermostat.
Can I install the Nest if my old thermostat has more than six wires?
Possibly, but it depends on what those extra wires do. If you have a heat pump with auxiliary heat, or a multi-stage system, you may need a professional. Check the Nest compatibility page on Google's website and upload a photo of your old thermostat's wiring — it will tell you whether your system is compatible.
My heating works but cooling does not. What do I check?
The Y wire controls cooling. Turn off power at the breaker, check that the Y wire is fully inserted into the Y terminal on the Nest base plate, and tighten the terminal screw. Turn power back on and test cooling again. If it still does not work, the wire may be damaged — try a different wire in the Y terminal if you have a spare, or contact a technician.
Do I need to do anything special if my furnace is in the attic?
No. The installation is the same whether your furnace is in the basement, attic, or closet. The only difference is that if you need the Power Connector, you will need to access your furnace's control board, which may be harder to reach in an attic. If you are not comfortable working in your attic, a technician can install the Power Connector for you.
What if the Nest screen stays blank after I turn power back on?
A blank screen usually means no power is reaching the thermostat. Check that the breaker is fully on — sometimes it trips partway and looks like it is on. If the breaker is on, turn it off, wait 30 seconds, and turn it back on. If the screen still does not light, check every wire connection at the base plate terminals and make sure each screw is tight. A single loose wire will prevent power from flowing.