The basic steps to reconnect Ring to WiFi
To move your Ring device to a new WiFi network, you need to put it back into setup mode, then tell it the new network name and password. The exact steps depend on whether you have a battery-powered Ring (like a Ring Video Doorbell) or a wired one (like a Ring Video Doorbell Wired), but both follow the same general path: reset the device, open the Ring app, start the setup process, and select your new network.
The fastest way is to use the Ring app on your phone. You do not need to physically reset the device in most cases — the app can trigger setup mode remotely. If the app cannot reach your device (because it is already disconnected from WiFi), you will need to press and hold the setup button on the device itself until the light blinks, which usually takes 15 to 20 seconds.
Once the device is in setup mode, the Ring app will detect it and walk you through selecting your new network and entering the password. The whole process typically takes 3 to 5 minutes if your password is correct and your WiFi signal is strong where the device is mounted.
Key Takeaways
- You can reconnect Ring to a new network using the Ring app without physically touching the device, as long as it is still powered and can reach your old network temporarily.
- If the app cannot find your device, press and hold the setup button on the back or bottom of the Ring until the light blinks orange, then use the app to complete setup.
- Ring devices need a 2.4 GHz WiFi network — they do not work on 5 GHz only networks, even if your router broadcasts both frequencies.
- If reconnection fails, check that your password is correct, that the device is within 30 feet of the router, and that no other devices are currently using the setup button.
Using the Ring app to reconnect without a physical reset
Open the Ring app on your phone and tap the menu icon (three horizontal lines) in the top left. Go to Devices, find your Ring device in the list, and tap on it. Scroll down and look for a "Reconnect to WiFi" or "Change WiFi Network" option — the exact wording varies by device type and app version, but it will be in the device settings.
Tap that option. The app will ask you to confirm that you want to put the device into setup mode. Say yes. The device will disconnect from your old network and enter pairing mode, and the app will prompt you to select your new WiFi network from the list of available networks nearby. Type in your new password and tap Connect.
The device will attempt to join the new network. This usually takes 30 to 60 seconds. Once it connects, the app will show a confirmation screen. If the connection fails, the app will tell you why — usually an incorrect password, weak signal, or a network that the device cannot use (like a 5 GHz only network).
Manually resetting the device if the app method does not work
If the Ring app cannot find your device, or if you prefer to reset it manually, locate the setup button on your Ring. On battery-powered Ring Video Doorbells, it is on the back. On wired Ring Video Doorbell models, it is usually on the bottom or back. On Ring Stick Up Cam, it is on the back. On Ring Floodlight Cam, it is on the side.
Press and hold the setup button for 15 to 20 seconds until the light on the front of the device blinks orange. This means the device is in setup mode and ready to pair. Release the button. Now open the Ring app, go to Devices, and tap the plus icon to add a new device. The app will search for nearby Ring devices in setup mode and should find yours within 10 to 15 seconds.
Once the app detects your device, tap on it to begin setup. You will be asked to select your new WiFi network and enter the password. After you enter the password, the device will connect to the new network. If it fails, try moving the device closer to the router — Ring devices need a strong signal to complete the initial connection, even if they work fine at a distance once connected.
Why 2.4 GHz matters and how to check your network
Ring devices only connect to 2.4 GHz WiFi networks. They do not support 5 GHz, even if your router broadcasts both at the same time. If your router is set to 5 GHz only, or if you have a mesh network that is not broadcasting 2.4 GHz on the same network name, your Ring will not be able to connect.
To check what your router is broadcasting, log into your router's settings (usually by typing your router's IP address into a web browser — check your router's manual for the exact address). Look for the wireless settings and confirm that 2.4 GHz is enabled. If you have a mesh system like Eero or Ubiquiti, check that both 2.4 GHz and 5 GHz are being broadcast under the same network name, or create a separate 2.4 GHz network just for Ring and other older smart home devices.
If you are not comfortable logging into your router, call your internet provider or the router manufacturer's support line. They can tell you over the phone whether your network is broadcasting 2.4 GHz and help you enable it if it is turned off.
Troubleshooting a failed connection
If your Ring keeps failing to connect to the new network, start by checking the password. Ring is case-sensitive, so if your password is "MyPassword123" and you type "mypassword123", it will fail. Re-enter it slowly and carefully, or copy and paste it from a note if you have it written down.
Next, check the distance between the Ring and your router. Ring devices need to be within 30 feet of the router during setup, even if they will work at a greater distance once connected. If your device is mounted far from the router, move it closer temporarily, complete the setup, and then move it back to its permanent location.
If the password is correct and the device is close to the router, restart both the device and the router. For a battery-powered Ring, remove the battery for 10 seconds and reinsert it. For a wired Ring, turn off power at the breaker for 10 seconds and turn it back on. Unplug your router, wait 30 seconds, and plug it back in. Then try the connection again.
If you still cannot connect, check whether another device in your home is currently using the setup button on a different Ring device. Only one Ring device can be in setup mode at a time. If you have multiple Ring devices, make sure the others are fully connected to WiFi before attempting to set up a new one.
What to do if your Ring loses connection after setup
If your Ring connects successfully but then loses the connection after a few minutes or hours, the problem is usually signal strength or network stability, not the setup process. Move the device closer to the router or add a WiFi extender in the location where your Ring is mounted.
You can also check whether your router is dropping 2.4 GHz devices. Some routers have a setting that prioritizes 5 GHz and deprioritizes or disconnects 2.4 GHz devices. Log into your router settings and look for any options related to band steering or 2.4 GHz priority. Disable band steering if it is on, or set the router to prefer 2.4 GHz devices.
If the connection is still unstable, restart the Ring device and the router again. If the problem persists after a second restart, contact Ring support through the app. Tap the menu icon, go to Help and Support, and select your device. Ring support can see your device's connection history and tell you whether the problem is on your network or with the device itself.
Reconnecting after a router change or network upgrade
If you are replacing your old router with a new one and want to keep the same network name and password, your Ring may reconnect automatically. When you set up the new router with the same network name (SSID) and password as the old one, Ring devices that are powered on will often find the new network and reconnect without any action from you.
However, if your new router uses different settings — a different network name, a different password, or a different frequency band — you will need to reconnect manually using the steps above. The same applies if you are switching internet providers or upgrading to a mesh network system.
Before you disconnect your old router, make sure all your Ring devices have successfully connected to the new network. You can check this in the Ring app by going to Devices and looking at the connection status of each device. Once all devices show as connected, you can safely disconnect and remove the old router.
Frequently Asked Questions
Can I connect my Ring to a guest network or separate 2.4 GHz network?
Yes. Ring devices can connect to any 2.4 GHz network, including guest networks and separate networks created specifically for smart home devices. If your router allows it, creating a separate 2.4 GHz network for Ring and other older smart devices can improve performance and security. Just follow the same connection steps using the guest or separate network name and password.
What if I forgot my new WiFi password?
You can reset your WiFi password through your router's settings or by calling your internet provider. Once you have the new password, use the Ring app to reconnect your device to the network. If you cannot access your router settings and do not remember the password, contact your internet provider — they can reset it for you or help you access your router remotely.
Do I need to remove my Ring from the app before reconnecting to a new network?
No. You do not need to remove the device from the app. straightforward use the "Reconnect to WiFi" option in the device settings, or perform a manual reset and let the app find the device again. The app will recognize it as the same device and reconnect it to your account automatically.
How long does it take for Ring to reconnect after I change networks?
The setup process itself takes 3 to 5 minutes. Once connected, the Ring device should be fully functional within 1 to 2 minutes. If you are reconnecting after a router change and the network name and password are the same, the device may reconnect automatically within 5 to 10 minutes without any action from you.
Will reconnecting to a new network erase my Ring's recordings or settings?
No. Reconnecting to a new network does not erase any recordings, motion detection settings, or other configurations. Your Ring will retain all of its settings and all of your recorded footage will remain in your Ring account. The reconnection only changes which WiFi network the device uses to communicate.