Where the paper goes and how to prepare it

The HP DesignJet 7000 series holds paper in a roll feed system at the back of the printer, not in a tray like a desktop printer. The roll sits on two spindles that run left to right across the machine. Before you load anything, measure your paper width — the 7000 series handles rolls from 17 inches to 44 inches wide, and you need to know which size you have so you can position the spindle supports correctly.

Paper for wide format printers comes in two forms: rolls (continuous) or sheets (cut to size). The 7000 series prefers rolls because they feed automatically, but it can also handle cut sheets if you load them one at a time through the rear tray. For this guide, we'll focus on roll loading, which is what most people use with this machine.

Before you touch the printer, unroll a few feet of paper on a clean, flat surface and let it sit for 15 minutes. Wide format paper can curl from being wound tightly, and letting it relax prevents jams and feeding problems. If your paper has been stored in a cold room, let it warm to room temperature first — cold paper is stiff and feeds poorly.

Key Takeaways

  • The HP DesignJet 7000 loads paper from a roll mounted on spindles at the back of the machine, and you must know your paper width before you start.
  • Slide the spindle supports to match your paper width, then mount the roll so the paper feeds from the bottom and pulls toward the front of the printer.
  • Thread the paper through the feed slot and into the media sensor, then press the load button on the control panel to find it.
  • The printer will pull the paper forward automatically and ask you to confirm the paper type and size on the touchscreen before it is ready to print.
  • If the paper jams or feeds crooked, stop when ready, open the rear access panel, and manually pull the paper out — do not force the spindle.

Positioning the spindle supports for your paper width

Open the rear access door on the back of the 7000 series. You will see two metal spindle supports — one on the left, one on the right — that can slide along the spindle rod. These supports must be positioned so the paper roll sits centered and does not overhang either side. If the roll is too loose or too far to one side, it will slip during feeding and cause misalignment.

Measure your paper width in inches. Most common widths are 24 inches, 36 inches, and 44 inches. Loosen the locking knobs on both spindle supports (they are usually large plastic knobs you turn counterclockwise by hand). Slide each support inward until they are roughly 1 inch closer to the center than the paper width — for example, if your paper is 24 inches wide, position the supports about 23 inches apart. This leaves a small gap on each side so the roll can sit without binding.

Once both supports are positioned, tighten the locking knobs firmly. The supports should not move when you push on them. If they slip, the paper will not feed straight, and you will see diagonal lines or skewing in your prints.

Mounting the roll and threading the paper

Lift the paper roll and slide it onto the spindle rod between the two supports. The roll should sit flat and centered. Make sure the paper unrolls from the bottom of the roll toward the front of the printer — if it unrolls from the top, the paper will feed upward and jam. You can tell which way it should go by looking at how the paper naturally wants to come off the roll.

Pull about 12 inches of paper from the roll and let it hang down in front of the printer. Open the front access panel (the door below the print head carriage). You will see a horizontal slot where the paper feeds in — this is the media feed path. Guide the paper straight into this slot, making sure it goes in level and does not fold or crease.

Continue feeding the paper forward until it reaches the media sensor — a small optical reader about 6 inches into the feed path. You will feel slight resistance as the paper passes through. Push gently until the paper is fully seated in the sensor. The printer needs to detect the paper here before it will accept a load command.

Pressing load and confirming paper settings

Close the front access panel. On the control panel touchscreen, you will see a menu with a "Load Media" or "Load Paper" button. Press it. The printer will pull the paper forward automatically and advance it until the leading edge reaches the print head. This usually takes 10 to 15 seconds. Do not open any doors or touch the paper while this is happening.

Once the paper stops moving, the touchscreen will ask you to confirm the paper type and size. Use the arrows on the screen to select your paper type — common options are "Coated Paper", "Matte Paper", "Glossy Paper", "Vinyl", or "Plain Paper". Then confirm the width in inches. If you select the wrong type, the printer will use incorrect tension and feed speed, and your prints may come out wrinkled or misaligned.

After you confirm, press "OK" or "Confirm". The printer will advance the paper a few more inches and then stop. The paper is now loaded and ready to print. The touchscreen will show the remaining length of the roll in feet or meters, so you can track how much paper you have left.

What to do if the paper jams or feeds crooked

If the paper jams during loading, stop when ready and do not try to force it through. Open the front access panel and look for where the paper is stuck. Usually it is folded or creased in the feed path. Gently pull the paper backward and out of the printer. If it is stuck tight, open the rear access panel as well so you can see both sides and work it free without tearing it.

If the paper feeds crooked — meaning it is not parallel to the spindle and is drifting left or right — stop the load and remove the paper. Check that the spindle supports are tight and positioned correctly. Also check that the roll itself is not damaged or dented on one edge, which can cause uneven feeding. Reposition the supports if needed and try again.

If the paper advances but the touchscreen does not detect it in the media sensor, the sensor may be dirty. Open the front access panel and look for a small optical window (usually clear or slightly frosted) in the feed path. Wipe it gently with a soft, dry cloth. Do not use water or solvents. Then close the panel and try loading again.

Loading cut sheets instead of rolls

The HP DesignJet 7000 can also print on cut sheets — single pieces of paper up to 44 inches wide. To load cut sheets, open the rear tray (a hinged panel at the back, separate from the roll feed area). Place one sheet at a time into the tray, making sure it is flat and aligned with the guides on either side. The sheet should not bend or curl.

Close the rear tray and press "Load Media" on the touchscreen. Select "Cut Sheet" from the media type menu, then confirm the width and height of your sheet. The printer will pull the sheet forward into the print head area. When the print is done, the sheet will eject out the front, and you can load the next one.

Cut sheet mode is slower than roll mode because the printer must stop and wait for you to load each new sheet. It is useful for small jobs or when you need different paper types for different prints, but for large jobs or production runs, roll feed is faster and more practical.

Storing paper rolls and preventing damage

When you are not using a paper roll, store it standing upright on its spindle in a cool, dry place. Do not lay it flat on the ground, because the weight will flatten the roll and cause feeding problems later. Keep paper away from direct sunlight, heat sources, and humidity — these cause the paper to warp, curl, or become brittle.

If you remove a partially used roll from the printer to switch to a different paper type, you can store it and reload it later. Before you remove it, note the paper type and width on a piece of tape and stick it to the roll so you remember what it is. When you reload it, position the spindle supports the same way and thread the paper through the feed path again — the printer will not remember the previous load.

Frequently Asked Questions

Can I load two different paper widths at the same time?

No. The HP DesignJet 7000 holds one roll at a time on the spindle. If you need to switch between paper widths, you must remove the current roll, reposition the spindle supports, and load the new roll. This takes about five minutes.

What happens if I load the paper upside down?

The paper will feed, but it may not print correctly if one side of the paper is coated or has a finish. The printer will pull it through the feed path regardless. If you notice the print quality is wrong, remove the paper, flip it, and reload it. Some papers are designed for one side only, so check your paper documentation.

How do I know if my paper is too narrow or too wide for the printer?

The 7000 series handles rolls from 17 inches to 44 inches wide. If your roll is narrower than 17 inches or wider than 44 inches, the spindle supports cannot position it correctly, and the printer will not load it. Check your paper specifications before you buy.

Why does the paper keep feeding crooked even after I tighten the spindle supports?

The roll itself may be damaged, dented, or wound unevenly. Inspect the edges of the roll for flat spots or dents. If the roll is damaged, it will not feed straight no matter how tight the supports are. You may need to use a different roll or contact the paper supplier for a replacement.

Can I use regular office paper in the 7000 series?

Yes, but it is not ideal. Regular office paper is thin and can wrinkle or tear in the wide format feed system. The 7000 series is designed for heavier papers — 80 pounds or more — that are stiff enough to feed smoothly. If you must use thin paper, load it as a cut sheet through the rear tray instead of as a roll.