Where the ink cartridges go and how to install them

Canon printers hold ink cartridges in a carriage that moves left and right inside the machine. To load ink, you open the printer's access door (usually the top or front panel), wait for the carriage to move to the center, and slide the cartridge straight up into its slot until you hear a click. The cartridge locks in place automatically. Most Canon printers use between two and five separate cartridges — one for each color plus black — so you may need to install several at once when you first set up the printer.

The exact location of the carriage and the number of cartridges depend on your specific Canon model. A multifunction printer (one that prints, scans, and copies) typically has four or five cartridges. A basic inkjet printer may have just two or three. Your printer's manual shows you exactly where each color goes, and the cartridges themselves are labeled and shaped differently so you cannot put them in the wrong slot by accident.

Key Takeaways

  • Open the printer's access panel and wait for the carriage to center itself before you touch any cartridges.
  • Each cartridge slides straight up into its labeled slot and clicks into place — do not force it or insert it at an angle.
  • Remove the plastic tape and protective cap from each new cartridge before installation, or the printer will not recognize it.
  • If the printer does not recognize a cartridge after installation, remove it, check that the gold contacts are clean and dry, and reinsert it firmly.

Preparing the printer and cartridges

Before you open any cartridge package, turn on your Canon printer and let it sit for 30 seconds. This gives the carriage time to move to its home position in the center of the printer. If you try to install cartridges while the carriage is still moving or in an unknown position, you risk jamming it or installing the cartridge incorrectly.

Once the printer is ready, open the access door or panel. On most Canon models this is the top cover that lifts up, but some printers have a front-loading door instead. The manual that came with your printer shows which one yours has. When you open the door, the carriage should move to the center automatically. If it does not move within a few seconds, close the door, turn the printer off and back on, and try again.

Unpack each new cartridge and remove the plastic tape that runs across the top. This tape protects the cartridge during shipping. You will also see a small plastic cap or seal on the bottom or side of the cartridge — remove this too. If you leave either the tape or the cap in place, the printer will not be able to read the cartridge or dispense ink from it, and you will get an error message on the printer's screen.

Installing each cartridge into its slot

Look inside the open printer and locate the cartridge slots. Each slot is labeled with a color: black, cyan (light blue), magenta (pink), and yellow. Some Canon printers also have a light cyan or light magenta cartridge. The cartridges are shaped and colored to match their slots, so you cannot put a yellow cartridge into the black slot even if you tried.

Hold the cartridge by its sides, not by the bottom or the gold contacts. Position it directly above its slot so the cartridge is vertical and straight. Push it down firmly and steadily until you hear a distinct click. The click means the cartridge has locked into place. Do not wiggle it side to side or try to force it down — if it does not slide in smoothly, remove it, check that the plastic cap is fully removed, and try again.

Repeat this process for each cartridge you need to install. If you are setting up a new printer, you will install all of them at once. If you are replacing a single empty cartridge, you only need to install that one. Once all cartridges are locked in, close the access door. The printer may run a brief initialization cycle, which is normal — this takes about one to two minutes.

What to do if the printer does not recognize the cartridge

After you close the door, the printer's screen should show that all cartridges are installed and ready. If you see an error message like "cartridge not recognized" or "cartridge error," the cartridge did not install correctly or the printer cannot read it.

First, open the access door again and check that the cartridge is fully clicked in. Push down on the top of the cartridge — if it moves at all, it is not locked. Remove it completely and reinstall it, pushing down until you hear the click. Close the door and check the screen again.

If the error persists, remove the cartridge and inspect the gold contacts on the bottom. These are small metal rectangles that the printer reads to identify the cartridge. If they are dirty, dusty, or wet, wipe them gently with a dry, lint-free cloth. Do not use water or cleaning solution. Reinstall the cartridge and check the screen.

If the cartridge still shows an error after you have reinstalled it twice and cleaned the contacts, the cartridge itself may be defective. Contact the retailer or manufacturer where you bought it for a replacement. Do not try to force the cartridge or use it if the printer continues to reject it.

Replacing a single cartridge when one runs out

When a cartridge is empty, the printer will display a message on its screen or send a notification to your computer. You do not have to replace it when ready — the printer will continue to work with the remaining cartridges, though it cannot print in the color that is empty. However, if you want to print in all colors, you need to replace the empty cartridge before you print.

Turn on the printer and open the access door. The carriage will move to the center. Locate the empty cartridge (the printer's screen usually tells you which one is empty) and push down on the top of it. It will pop out slightly. Grip it by the sides and pull it straight out toward you. Do not tilt it or pull at an angle.

Unpack the new cartridge, remove the plastic tape and protective cap, and install it the same way you did the first time — straight up into the slot until you hear the click. Close the door. The printer may show a brief message while it recognizes the new cartridge, and then you are ready to print again.

Storing extra cartridges and avoiding common mistakes

Keep unopened cartridges in a cool, dry place away from direct sunlight. The ideal temperature is between 60 and 75 degrees Fahrenheit. Do not store cartridges in a hot garage, a damp basement, or near a window where sunlight hits them regularly. Heat and moisture can damage the ink inside and make the cartridge unusable.

Once you open a cartridge, use it within six months if possible. Opened cartridges can dry out over time, especially if the protective cap is not replaced. If you have an opened cartridge that you are not using, put the plastic cap back on and store it in an airtight container or a sealed plastic bag.

Do not touch the gold contacts on the bottom of the cartridge with your fingers, and do not let them get wet. Do not remove the cartridge and leave it out of the printer for more than a few hours, because the ink can begin to dry. If you need to remove a cartridge temporarily, put the plastic cap back on when ready.

Frequently Asked Questions

Can I use third-party or refilled cartridges in my Canon printer?

Yes, many Canon printers accept third-party and refilled cartridges, though Canon's warranty may not cover damage caused by non-Canon cartridges. Third-party cartridges install the same way as Canon cartridges — straight up into the slot until they click. Check your printer's manual to see whether it lists compatible cartridge brands, or contact Canon support with your printer model number.

Why does my printer say the cartridge is not recognized even though I installed it correctly?

The most common cause is that the plastic protective cap was not fully removed from the bottom of the cartridge. Check the bottom again and make sure there is no plastic seal left. If the cap is off, remove the cartridge, wipe the gold contacts with a dry cloth, and reinstall it. If the error continues after two reinstallations, the cartridge may be defective and you should request a replacement from the retailer.

Do I have to replace all the cartridges at the same time?

No. You only replace the cartridge that is empty. The others can stay in the printer and continue working. However, if one cartridge is empty, you cannot print in that color until you replace it, even if the other cartridges are full.

What should I do with the old cartridge after I remove it?

Many retailers that sell ink cartridges, including office supply stores and some electronics retailers, accept used cartridges for recycling at no charge. Some manufacturers also offer mail-back recycling programs. Check your local recycling program to see whether cartridges can go in curbside recycling — most programs do not accept them because of the residual ink inside.

How do I know which cartridge is which color if I cannot see the labels?

Each cartridge is a different color and shape, and each slot is labeled inside the printer. The black cartridge is usually larger than the color cartridges. If you are unsure, your printer's manual has a diagram showing exactly where each color goes. You can also look at the cartridge itself — it will have the color name printed on the side or top.