How to install a Canon ink cartridge
Installing a Canon ink cartridge takes about five minutes and requires no tools. Turn off the printer, open the access door on the front or top (depending on your model), and the cartridge holder will move to the center. Remove the old cartridge by pressing down on it until it clicks and pops out. Unwrap the new cartridge, remove the yellow protective tape from the bottom, and insert it into the empty slot at a 45-degree angle, then press down until it clicks into place. Close the access door and turn the printer back on — it will run a setup cycle that takes a minute or two.
The exact location of the access door and the number of cartridges your printer holds depend on your model. Canon makes single-cartridge printers, four-cartridge printers (one black, three colors), and five-cartridge printers (black, cyan, magenta, yellow, and a second black for photo printing). Check your printer's manual or the label on the printer itself to see which type you have.
Key Takeaways
- Turn off the printer before opening the cartridge door, and wait for the cartridge holder to stop moving before you touch anything inside.
- The yellow protective tape on the bottom of a new cartridge must be removed before installation, or the cartridge will not work.
- Cartridges insert at a 45-degree angle and click into place — if you feel resistance, you are inserting at the wrong angle.
- After installation, the printer runs a setup cycle that can take one to three minutes; do not turn it off during this time.
- Keep the old cartridge in case you need to return it for recycling or if the new one is defective.
Locate the cartridge access door on your specific model
Canon printers store the cartridge door in different places depending on the series. On most inkjet models (Pixma MG, MX, and TR series), the door is on the front of the printer below the scanner lid. On some older models and photo printers, the door is on the top. Open your printer's manual or search the model number on Canon's website to see a diagram of where the door is located on your printer.
Once you find the door, look for a small latch or handle. Some doors slide open; others swing open like a cabinet. The manual will show you which direction to pull. If you force it the wrong way, you risk breaking the latch.
Power off the printer and wait for the cartridge holder to stop
Press the power button on the printer and wait for it to shut down completely. Do not unplug it — the cartridge holder needs power to move to the center position where you can reach it. Once the printer is off, open the cartridge access door. The holder should move automatically to the middle of the printer. If it does not move within a few seconds, close the door, turn the printer back on, and try again.
Wait at least 10 seconds after the holder stops moving before you touch any cartridges. The holder can move unexpectedly if the printer is still initializing.
Remove the old cartridge
Look at the cartridge holder and identify which slot holds the cartridge you need to replace. Each slot is labeled with a color or symbol (usually a small icon on the holder itself). Press down on the cartridge you want to remove — you will feel it click. Continue pressing until the cartridge pops out and tilts toward you at an angle. Grab the cartridge by its sides (not the nozzles on the bottom) and pull it straight out.
Set the old cartridge on a paper towel or newspaper. Ink can leak from the nozzles, especially if the cartridge was recently in use. Do not touch the nozzles or the gold contacts on the back of the cartridge. If you plan to recycle the cartridge, keep it in a sealed bag until you are ready to drop it off.
Prepare and insert the new cartridge
Remove the new cartridge from its box and inspect it for damage. Look for a yellow or orange protective tape on the bottom of the cartridge — this tape covers the nozzles and prevents ink from drying out during shipping. Peel off this tape completely. If you leave it on, the cartridge will not dispense ink and the printer will show an error.
Hold the new cartridge by its sides and position it at a 45-degree angle to the empty slot. The cartridge should point downward and to the side, not straight down. Align the cartridge with the slot and push it in gently. When it is fully inserted, press down until you hear a click. The cartridge should now be level with the other cartridges in the holder, not tilted.
If you feel strong resistance before the click, stop and check the angle. Forcing a cartridge at the wrong angle can damage the slot or the cartridge. Remove it, reposition it at 45 degrees, and try again.
Close the door and run the setup cycle
Close the cartridge access door firmly until you hear it latch. Turn the printer back on. The printer will detect the new cartridge and run an automatic setup cycle. During this cycle, the printer cleans the nozzles and tests the cartridge. This usually takes one to three minutes. You will see lights blinking or hear the printer moving inside — this is normal. Do not turn off the printer or open the door during this cycle.
Once the setup cycle is complete, the printer will return to its normal ready state. Print a test page to confirm the new cartridge is working. If the color or black is missing or faint, the cartridge may not have installed correctly. Open the door, remove the cartridge, and reinstall it, making sure you hear the click.
Troubleshooting common installation problems
If the printer shows an error message after installation, the cartridge may not be fully seated. Open the door, press down on the cartridge again until you hear a second click, and close the door. If the error persists, remove the cartridge and check that the yellow protective tape was completely removed from the bottom. Even a small piece of tape left behind will block ink flow.
If the cartridge holder does not move to the center when you open the door, the printer may not have enough power or may be in an error state. Close the door, turn the printer off, wait 30 seconds, and turn it back on. Then open the door again. If the holder still does not move, check that the power cable is plugged in and that the outlet is working.
If ink leaks from the nozzles after installation, the cartridge may have been damaged during shipping or installation. Contact Canon support with your cartridge lot number (printed on the box) and your printer model number. They can arrange a replacement.
Frequently Asked Questions
Do I need to turn off the printer before changing a cartridge?
Yes. Turning off the printer allows the cartridge holder to move to the center position where you can safely reach the cartridges. If you try to change a cartridge while the printer is on, you risk damaging the holder or the cartridge.
What if I install the cartridge upside down?
The cartridge will not fit into the slot if it is upside down — the shape of the cartridge and the slot are designed to prevent this. If you cannot insert the cartridge, check the angle and orientation. The nozzles (the flat part on the bottom) should face into the printer.
Can I use third-party or refilled cartridges in my Canon printer?
Canon printers accept third-party and refilled cartridges, though Canon does not warrant them. Some third-party cartridges may trigger warning messages on the printer, but they will usually still work. If a cartridge does not install or causes errors, try a Canon-brand cartridge to rule out compatibility issues.
How long does the setup cycle take after I install a new cartridge?
The setup cycle usually takes one to three minutes. During this time, the printer cleans the nozzles and tests the cartridge. You will see lights blinking or hear movement inside the printer. Wait for the cycle to finish before printing.
What should I do with the old cartridge after I remove it?
Store the old cartridge in a sealed plastic bag to prevent ink from leaking onto other surfaces. Many retailers that sell ink cartridges (including Best Buy, Staples, and Office Depot) accept used cartridges for recycling at no charge. Some manufacturers also offer mail-back programs. Check Canon's website for recycling options in your area.