A black monitor usually means the cable came loose, the input source switched, or the computer went to sleep — not that the monitor itself broke
When your monitor goes black, the problem is almost always one of five things: the video cable disconnected, you're looking at the wrong input, the computer entered sleep mode, the monitor's brightness dial got turned down, or the monitor lost power. You can rule out each one in about two minutes. Start with the simplest checks first — a loose cable causes more black screens than any hardware failure.
The good news is that a black monitor does not mean you need a new one. Most of the time you are dealing with a connection issue or a setting that changed. Even if the monitor itself has a problem, you can usually get video working again by switching to a different cable or input port while you figure out the next step.
Key Takeaways
- Check that the video cable is pushed firmly into both the monitor and the computer — a half-inserted cable is the most common cause of a black screen.
- Press the input button on your monitor to cycle through HDMI, DisplayPort, DVI, or VGA and confirm you are watching the right port.
- Move your mouse or press a key on the keyboard to wake the computer from sleep mode, which looks identical to a black screen.
- Look for a brightness dial or button on the monitor itself — many monitors have a physical brightness control that can be turned all the way down.
- Check that the monitor's power cable is plugged in and the power button is pressed, and look for a power light on the monitor's frame.
The video cable is loose or not fully inserted
The cable that runs from your computer to your monitor can work itself loose over time, especially if you move your desk or unplug things regularly. Even a cable that looks plugged in might not be making full contact inside the port. This is the single most common reason for a black screen.
Turn off both the monitor and the computer. Look at the back of the monitor and find the video cable — it will be labeled HDMI, DisplayPort, DVI, or VGA depending on your setup. Unplug it completely from the monitor. Then unplug it from the computer. Wait five seconds. Plug it back into the computer first, pushing it in until you hear or feel a click. Then plug it into the monitor the same way. Turn both devices back on. If the cable was the problem, you should see the monitor light up within a few seconds.
If you have more than one video cable lying around, try a different one. Sometimes a cable works most of the time but has a loose connection inside that causes intermittent black screens. Swapping cables is a fast way to know whether the cable itself is the problem.
The monitor is set to the wrong input source
Modern monitors can accept video from multiple ports at the same time — HDMI, DisplayPort, DVI, and VGA are all common. Your monitor is only displaying one of them at any moment. If your computer is plugged into HDMI but the monitor is set to look at DisplayPort, you will see a black screen even though everything is connected correctly.
Look for a button labeled "Input" or "Source" on the monitor's frame, usually on the bottom or side. Press it. A menu should appear on the screen showing you which inputs are available and which one is currently active. Use the arrow buttons to highlight the input that matches your cable — if you plugged into the HDMI port, select HDMI. Press Enter or the button again to confirm. The picture should appear.
If you are not sure which input you used, cycle through them one at a time. Press the input button, select the next option, and wait a few seconds to see if a picture appears. Most monitors will show you the input name on screen as you switch, so you can see which one you are trying.
The computer is in sleep mode
Sleep mode is designed to save power when you step away from your desk. The monitor goes black, the hard drive spins down, and the computer uses almost no electricity. From across the room, sleep mode looks exactly like a broken monitor. The difference is that sleep mode wakes up when ready when you touch something.
Move your mouse or press any key on the keyboard. If the computer was asleep, the monitor should light up within a second or two and show you the login screen or your desktop. If nothing happens, the computer is probably off or has a different problem.
If your computer keeps going to sleep too quickly, you can change the sleep settings. On Windows, right-click the desktop, select "Display settings," scroll down to "Power," and choose how long the computer waits before sleeping. On Mac, open System Settings, go to "Lock Screen," and adjust the "Turn display off after" setting. You can also disable sleep entirely if you prefer, though it uses more power.
The monitor's brightness is turned all the way down
Many monitors have a physical brightness dial or button on the frame, separate from any software settings on your computer. If someone turned this dial all the way down, or if it got bumped accidentally, the screen will appear completely black even though the monitor is working fine.
Look at the bottom, side, or back of your monitor for a dial or a row of buttons. One of them is usually labeled with a sun symbol or the word "Brightness." Try turning a dial clockwise or pressing a button labeled with a plus sign or up arrow. You should see the image gradually appear as you increase the brightness. If you find a dial, turn it slowly until you can see your desktop.
Some monitors also have an on-screen menu that controls brightness. If you see a menu appear when you press buttons on the monitor, look for a brightness or picture option and adjust it upward.
The monitor has no power
A monitor that is not plugged in or switched off will show a completely black screen. This is the easiest problem to fix but also the easiest to overlook because you might assume the monitor is on.
Check that the power cable is plugged into the back of the monitor and into a working wall outlet or power strip. Look for a small light on the monitor's frame — usually near the power button or on the bottom edge. This light is often blue or green when the monitor is on and receiving power. If you do not see a light, the monitor is not getting power.
Press the power button on the monitor itself. It is usually on the bottom or side of the frame. You should hear a faint beep or see the light turn on. If the monitor still does not turn on after you press the button, try plugging it into a different outlet to rule out a bad power strip or outlet. If it works in the new outlet, the original outlet or power strip may be broken.
The video port or cable is damaged
If you have checked the cable connection, tried a different cable, confirmed the input source, and the screen is still black, the problem might be a damaged port on the monitor or computer. Ports can break if a cable is forced in at an angle, if something spilled on the monitor, or straightforward from age.
Look closely at the ports on the back of both the monitor and the computer. The pins or connectors inside should be straight and not bent or corroded. If you see bent pins, corrosion, or obvious damage, that port is probably not working. Try plugging into a different port if your monitor or computer has more than one video port available.
If your computer has multiple video ports — for example, both HDMI and DisplayPort — try the other one. If your monitor has multiple inputs, try a different cable in a different port. This helps you figure out whether the problem is with one specific port or with the cable itself. If switching ports fixes the problem, the original port is damaged and you may need to have it repaired or use a different port going forward.
Frequently Asked Questions
Why does my monitor go black for a few seconds and then come back on?
This usually means the cable connection is loose or slightly damaged. The video signal cuts out briefly when the connection shifts. Try unplugging and firmly reinserting the cable at both ends. If it keeps happening, try a different cable to see if the problem follows the cable or stays with the port.
My monitor is black but I can hear the computer running. What should I check first?
First, move your mouse or press a key to wake the computer from sleep. If that does not work, check that the monitor's power light is on. Then check the video cable connection at both the monitor and computer. Finally, press the input button on the monitor to make sure you are looking at the right port.
Can a black monitor mean the graphics card failed?
It is possible but unlikely. A failed graphics card usually causes a black screen only after the computer has been on for a while and gets hot. If the screen is black from the moment you turn on the computer, a loose cable or wrong input source is far more probable. Try the cable and input checks first.
What if I plugged in a new monitor and it shows nothing?
New monitors are sometimes set to an input that is not connected. Press the input button and cycle through the available options until you find the one your cable is plugged into. Also check that the monitor's power cable is fully inserted and the power button is pressed. Many people forget to press the power button on a brand-new monitor.
Is it safe to keep using a monitor that goes black randomly?
If it is a loose cable, yes — just fix the connection. If the screen goes black because of a damaged port or cable, it is still safe to use as long as you have a working alternative port or cable available. However, if the monitor itself is damaged internally, continued use could make it worse. If you cannot identify the cause after checking cables and inputs, consider having it inspected.