The basic power-on steps

Most monitors turn on the same way: find the power button, press it, and wait for the light to come on. The button is usually on the front of the monitor, often at the bottom center or bottom right. Some monitors have the button on the side. Press it once — you do not need to hold it down.

After you press the button, the monitor takes a few seconds to start. You will see a light turn on (usually blue or white), and the screen will go from black to showing an image. If nothing appears after 10 seconds, the monitor is on but not receiving a signal from your computer yet. That is a separate problem covered below.

If your monitor has a power cord, make sure it is plugged into a working outlet. If it is plugged into a power strip, check that the power strip itself is turned on — look for a switch on the strip and make sure it is in the on position.

Key Takeaways

  • The power button is usually on the front of the monitor at the bottom center or bottom right, and you only need to press it once.
  • The monitor light will turn on within a few seconds, but the screen may stay black if your computer is not sending a signal to it.
  • Check that the power cord is plugged in and that any power strip the monitor uses is switched on.
  • If the monitor turns on but shows no picture, the cable connecting it to your computer may be loose or plugged into the wrong port.
  • Restarting your computer after connecting a new monitor often fixes picture problems that happen on first setup.

What to do if the monitor turns on but shows no picture

A monitor that lights up but stays black is usually not receiving a signal from your computer. The first thing to check is the cable. Look at the back of your monitor where the cable plugs in. Unplug the cable, wait a few seconds, and plug it back in firmly. Sometimes a loose connection is all it takes.

Next, check where the cable plugs into your computer. Most monitors use an HDMI cable or a DisplayPort cable. Look at the back or side of your computer (or the back of your keyboard if you have an all-in-one desktop) and find the port that matches your cable. If the cable is plugged into a different port, unplug it and move it to the correct one. If you are not sure which port is correct, look for one labeled HDMI or DisplayPort, or check your computer's manual.

If you just connected a new monitor for the first time, restart your computer. Many computers do not detect a new monitor until they start up again. Turn off your computer completely, wait 30 seconds, and turn it back on. Once it finishes starting, your monitor should show a picture.

Checking the monitor settings and brightness

If your monitor is on and receiving a signal but the screen is very dark or hard to see, the brightness may be turned down. Look for buttons on the front or side of the monitor. One of them usually controls brightness — it may be labeled with a sun symbol or the word "brightness". Press the button that increases brightness and hold it for a few seconds. The image should get brighter.

Some monitors also have a menu button that opens on-screen settings. If you see a menu appear on your screen, look for brightness or contrast options. Use the arrow buttons to adjust them, then press enter or the menu button again to close the menu and save your changes.

What to do if the monitor will not turn on at all

If you press the power button and nothing happens — no light, no sound, no change — the monitor is not getting power. First, check the outlet. Plug a lamp or phone charger into the same outlet to see if it works. If the outlet is dead, try a different outlet in the same room or a different room.

If other devices work in that outlet, the problem is with the monitor's power cord or the monitor itself. Check that the power cord is fully inserted into both the outlet and the back of the monitor. If it is, try a different power cord if you have one available — sometimes cords fail without obvious damage. If a different cord works, your original cord is broken and needs to be replaced.

If the monitor still will not turn on after trying a different outlet and checking the cord, the monitor itself may be faulty. This is rare with new monitors but common with older ones. At this point, you may need to contact the manufacturer or consider replacing the monitor.

Connecting a monitor to a laptop

Laptops connect to external monitors the same way desktops do — through an HDMI or DisplayPort cable. Plug the cable into the port on the side of your laptop, then plug the other end into the monitor. Turn on the monitor and restart your laptop if you do not see a picture right away.

Some laptops need you to press a key combination to send video to the external monitor. The most common is Fn + F3, Fn + F4, or Fn + F7, depending on your laptop brand. Look for a key with a monitor symbol on it, hold Fn, and press that key. You may need to press it a few times to cycle through different display modes — laptop screen only, external monitor only, or both at once.

Understanding monitor lights and what they mean

Most monitors have a small light on the front that tells you the power state. A solid blue or white light means the monitor is on and working. A blinking or amber light usually means the monitor is in sleep mode — it is on but not receiving a signal. Press a button on the monitor or move your mouse to wake it up.

If the light is off completely, the monitor has no power. If the light is red, some monitors use that to indicate a problem, though this is less common. Check your monitor's manual to see what the red light means for your specific model.

Frequently Asked Questions

Why does my monitor turn on but my computer screen stays black?

The cable between your monitor and computer is probably loose or plugged into the wrong port. Unplug the cable from both ends, wait a few seconds, and plug it back in firmly. If that does not work, try plugging the cable into a different video port on your computer. Restart your computer after making the change.

Can I turn on a monitor without a computer?

Yes, you can turn on the monitor itself, and the light will come on. However, the screen will stay black or show a "no signal" message because there is no computer sending it a picture. This is normal and does not mean anything is broken.

What if my monitor has a button that says "input" or "source"?

That button lets you choose which cable the monitor displays from — HDMI 1, HDMI 2, DisplayPort, and so on. If you have only one cable plugged in, you usually do not need to change this. If you have multiple cables connected and the wrong one is showing, press the input button and use the arrow buttons to select the correct source.

Is it bad to leave my monitor on all the time?

Leaving a monitor on continuously can shorten its lifespan and waste electricity, but it will not cause when ready damage. Most monitors are designed to go into sleep mode after a period of no activity, which uses much less power. You can set this in your computer's power settings.

Why does my monitor show a picture for a second then go black?

This usually happens when the cable is loose or partially disconnected. The monitor briefly receives a signal, then loses it. Turn off both the monitor and computer, unplug the video cable from both ends, and plug it back in very firmly. Make sure it clicks or seats fully into the port.