Apple Watch bands release with a single button press
You can swap an Apple Watch band without tools, without taking it to a store, and without removing the watch from your wrist if you don't want to. Every Apple Watch band uses the same release mechanism: a small button on the underside of the watch case that you press to slide the band out sideways. The whole process takes about 10 seconds once you know where the button is.
The button sits in a small rectangular slot on the underside of the watch case, toward the edge closest to your wrist. You'll see two slots — one on each side of the watch. Each slot holds one band. Press the button inside the slot, and the band slides straight out toward your wrist. Slide a new band in from the same direction, and it clicks into place.
Apple Watch bands are not interchangeable across all models. The band width changed between the original Apple Watch and the Series 1, and again between Series 4 and Series 5. Check your watch model in Settings > General > About to confirm which size you need before buying a replacement band.
Key Takeaways
- Press the small button inside the slot on the underside of your watch to release the band, then slide it out toward your wrist.
- Apple Watch bands come in two widths: 38mm/40mm and 42mm/44mm, and they are not interchangeable between sizes.
- You can wear the watch on either wrist without removing the band, and the watch will automatically adjust the display orientation.
- Third-party bands work the same way as Apple bands and cost less, though some fit more loosely than others.
Which band size fits your watch model
Apple Watch comes in two case sizes, and each size uses a different band width. The smaller size — 38mm on the original through Series 3, and 40mm on Series 4 and later — uses a narrower band. The larger size — 42mm on the original through Series 3, and 44mm on Series 4 and later — uses a wider band. Buying the wrong size will not damage your watch, but the band will not fit into the slots.
Find your watch size in Settings > General > About. Look for "Model" and read the number: if it says 38mm or 40mm, you need the smaller band width. If it says 42mm or 44mm, you need the larger width. Some retailers list bands by both the old and new naming — "38/40mm compatible" or "42/44mm compatible" — so check both numbers on the product page before ordering.
Ultra models use the same band width as the 44mm watches, so an Ultra takes a 44mm band. The SE uses the same width as the standard model of its generation: SE (1st generation) uses 38mm bands, and SE (2nd generation) uses 40mm bands.
How to remove and install a band step by step
Hold your watch with the underside facing up. You'll see two rectangular slots running along the sides of the case, one on each side. Inside each slot is a small button. Press and hold the button in the slot closest to the band you want to remove. The band will slide out toward your wrist. If it doesn't move, you may be pressing the wrong button — make sure you're pressing inside the slot, not beside it.
Once the band is out, pick up the new band and align it with the empty slot. Slide it in from the direction the old band came out — straight in toward the watch case. You'll feel it click when it seats fully. Tug gently on the band to confirm it's locked. If it slides back out, it wasn't fully inserted; try again, pushing a bit harder until you hear the click.
The watch will work on either wrist. If you switch wrists, go to Settings > General > Orientation and toggle "Left" or "Right" to match. The display will flip automatically so the Digital Crown stays on the correct side.
Third-party bands and what to expect
Any band made for your watch size will fit into the slots, including third-party options from brands like Nomad, Spigen, and Monowear. Third-party bands cost less than Apple bands — often $15 to $40 compared to $50 to $150 for official Apple bands — and come in more colors and materials. The fit and finish vary by brand. Some feel as solid as Apple bands; others have slightly more play in the slot and may rotate a tiny bit on your wrist.
Read reviews before buying, especially for leather or fabric bands. Some third-party leather bands develop creases or discoloration faster than Apple's. Fabric bands from less-known brands sometimes shed dye onto your skin. Sport bands from major third-party makers are usually reliable and hold up well to sweat and water.
If a third-party band feels loose, you can add a thin adhesive-backed foam pad to the back of the band to tighten the fit. Cut a small rectangle from a foam phone screen protector and stick it to the inside of the band where it contacts the watch case. This is a temporary fix and works better on some bands than others.
Cleaning your watch and bands
Remove the band before cleaning your watch. Wipe the watch case and the band slots with a soft, lint-free cloth slightly dampened with water. For stubborn dirt, use a cloth dampened with a 50/50 mix of water and isopropyl alcohol. Dry everything with a dry cloth before reinserting the band.
Sport bands can be rinsed under running water and air-dried. Leather bands should be wiped with a damp cloth only — never submerged. Fabric bands can be hand-washed in cool water with mild soap, then air-dried flat. Metal bands can be cleaned the same way as the watch case, or soaked briefly in warm soapy water if they're very dirty.
The band slots on the watch case can collect lint and dust. Use a dry toothbrush or a soft brush to gently clean inside the slots before inserting a new band. This keeps the band from sitting at an angle and helps it click in fully.
Troubleshooting a band that won't release or insert
If a band won't slide out, you may be pressing the button too lightly or in the wrong spot. The button is small and recessed. Press firmly and hold for a full second. If the band still won't budge, try pressing the button on the opposite side of the watch — you may have been aiming at the wrong slot.
If a new band won't slide in, check that you're using the correct size for your watch. A band made for a 38mm watch will not fit a 42mm watch. If the size is correct, make sure the slot is completely empty — sometimes a band doesn't fully eject on the first try. Press the button again and pull the old band all the way out before inserting the new one.
Dirt or lint inside the slot can also prevent a band from seating. Use a dry toothbrush or a blast of compressed air to clean the slot, then try again. If a band clicks in but feels loose or rotates, it may be slightly worn or the watch slot may have debris. Remove the band, clean the slot thoroughly, and reinsert it.
Frequently Asked Questions
Can I wear my Apple Watch without a band?
No. The band slots are part of the watch structure, and removing both bands leaves the watch unstable and prone to damage. You need at least one band installed at all times. If you want a minimal look, Apple sells a single-loop band that wraps around the case with no visible buckle.
What happens if I lose a band?
You can buy a replacement band from Apple or a third-party maker. Apple bands range from $50 to $150 depending on material. Third-party bands cost $15 to $60. Make sure you buy the correct size for your watch model before ordering.
Do I need to remove the band before charging my watch?
No. The charging cable connects to the back of the watch case, not to the band. You can charge your watch with any band installed. Removing the band before charging is optional and makes no difference to how fast it charges.
Can I wear the same band on both a 40mm and 44mm watch?
No. The band widths are different, and a 40mm band will not fit into the slots of a 44mm watch. You need separate bands for each watch size.
What's the best way to store extra bands?
Store bands in a cool, dry place away from direct sunlight. Keep leather bands in a drawer or box where they won't dry out. Sport bands can be stored anywhere. If you store bands for months without wearing them, check them occasionally for dust or mold, especially fabric bands in humid climates.