Open the faceplate and remove the old battery
The battery in a Ring doorbell sits behind the faceplate — the front cover you see when looking at the device. To access it, locate the small slot or notch at the bottom of the faceplate and gently pry it away from the doorbell body using a flathead screwdriver or a plastic pry tool. The faceplate clips into place and will pop off with light pressure; do not force it or you risk cracking the plastic.
Once the faceplate is off, you will see the battery mounted horizontally inside the device. Most Ring doorbells use a rechargeable lithium-ion battery that slides out of a plastic holder. Grip the battery by its sides and slide it straight out toward you. Do not pull on any wires attached to the battery — they disconnect automatically as the battery clears the contacts.
Key Takeaways
- Ring doorbell batteries slide out horizontally from behind the faceplate after you pry the cover off with a flathead screwdriver.
- The battery is rechargeable and lasts between six months and two years depending on how many motion events and video recordings your doorbell handles.
- You can charge the battery inside the doorbell using the included USB cable, or remove it and charge it separately with a standard USB charger.
- If your doorbell stops responding to motion or video requests, a low or dead battery is the most common cause and the first thing to check.
Charge the battery or install a replacement
Ring batteries are rechargeable, so in most cases you do not need to buy a new one — you charge the one you have. The easiest method is to leave the battery in the doorbell and plug the included USB cable into the port on the bottom of the device. Charging takes four to twelve hours depending on how depleted the battery was. You will see a blue LED light on the doorbell while it charges; the light turns off when the battery is full.
If you prefer to charge the battery outside the doorbell, slide it back into its holder and connect the USB cable directly to the battery's charging port instead of the doorbell. This takes the same amount of time but lets you charge while the doorbell is still mounted on your wall. If the battery no longer holds a charge after multiple full charging cycles, you can order a replacement battery from Ring's website or from retailers that carry Ring accessories — the replacement costs between $20 and $30 depending on your doorbell model.
Reinstall the battery and close the faceplate
Slide the charged battery back into its holder with the contacts facing toward the back of the doorbell. You will feel it click into place when it is seated correctly. The battery should sit flush with the holder and not stick out or sit at an angle. If it does not slide in smoothly, remove it and check that the contacts are clean and free of dust or corrosion.
Once the battery is installed, press the faceplate back onto the doorbell body. Start at the top and work your way down, pressing firmly until you hear or feel the clips snap into place. The faceplate should sit flush with the doorbell body with no gaps. Your Ring doorbell will restart automatically once power is restored, and you should see the blue LED light briefly as it boots up.
Why your Ring doorbell battery drains faster than expected
Ring doorbell batteries last between six months and two years, but the actual time depends on how much your doorbell is used. Every motion detection event, video recording, and live view session drains the battery. If your doorbell is mounted near a busy street, a frequently-used walkway, or an area with blowing leaves or shadows, it will trigger motion alerts constantly and drain the battery much faster than a doorbell in a quiet location.
Cold weather also reduces battery life — lithium-ion batteries perform poorly in temperatures below 40 degrees Fahrenheit and may appear dead even when they still have charge. If your doorbell stops responding during winter, bring the battery indoors to warm up for an hour, then try charging it again. You can also reduce battery drain by adjusting your motion detection settings in the Ring app: lower the sensitivity, reduce the detection zone, or turn off motion alerts during hours when you do not need them.
What to do if your doorbell will not hold a charge
If the battery charges fully but the doorbell dies within hours or a few days, the battery itself may be failing. Before you replace it, check that the charging contacts on both the battery and the doorbell are clean. Dust, corrosion, or debris on the contacts prevents proper charging. Use a dry cotton swab or a soft brush to gently clean both sets of contacts, then try charging again.
If cleaning the contacts does not help, the battery has likely reached the end of its lifespan and needs replacement. Order a new battery from Ring or an authorized retailer and install it using the same steps you used to remove the old one. If a new battery still does not hold a charge, the doorbell itself may have a hardware problem — in that case, contact Ring support with your doorbell model number and serial number, which you can find in the Ring app under Device Settings.
Hardwired doorbells and battery backup
Some Ring doorbell models can be hardwired directly to your home's existing doorbell wiring, which powers the device continuously and charges the battery automatically. If your doorbell is hardwired, the battery acts as a backup in case your power goes out — it keeps the doorbell working for a limited time until power returns. Hardwired doorbells rarely need manual battery charging because the constant power supply keeps the battery topped up.
If you have a hardwired Ring doorbell and the battery is draining despite being plugged in, the wiring connection may be loose or the transformer powering your doorbell may be failing. Check that the wires are firmly seated in the terminal block on the back of the doorbell, and test your doorbell transformer with a multimeter if you have one. If the transformer is outputting less than 16 volts, it cannot charge the battery properly and needs replacement.
Frequently Asked Questions
How do I know if my Ring doorbell battery is dead?
A dead battery means the doorbell will not respond to motion, will not record video, and will not let you view the live feed from the Ring app. The device may still show as "online" in the app for a few hours after the battery dies, but you cannot interact with it. If your doorbell suddenly stops responding, low battery is the first thing to check.
Can I use a different brand of battery in my Ring doorbell?
No. Ring doorbells use proprietary batteries designed specifically for that model, and using a different battery can damage the device or create a safety hazard. Always use a Ring-brand replacement battery or a battery sold by an authorized Ring retailer that is listed as compatible with your doorbell model.
What happens if I leave the battery out of my Ring doorbell?
Without a battery, a hardwired Ring doorbell will still work as long as your home's doorbell wiring is connected. A battery-only doorbell (one not hardwired) will not work at all and cannot detect motion or record video. If you remove the battery for charging, the doorbell is offline until you reinstall it.
Does the Ring app tell me when the battery is low?
Yes. The Ring app shows battery percentage in the Device Health section, and you will receive a notification when the battery drops below 20 percent. You can also check the battery level anytime by opening the Ring app, selecting your doorbell, and tapping Device Health.
Can I charge my Ring doorbell battery with a phone charger?
Yes, if your phone charger has a USB port that matches the doorbell's charging port. Ring doorbells use standard USB-C or micro-USB charging depending on the model. Check your doorbell's manual or the Ring website to confirm which type your model uses, then use any compatible USB charger with the included cable.