The pairing process happens automatically when you open the case near your iPhone or iPad

When you unbox new AirPods, they arrive already paired to each other inside the case. What you need to do is pair that case—and the AirPods inside it—to your phone or tablet. The simplest way: open the case lid near an unlocked iPhone or iPad, and a setup screen appears on your device within a few seconds. Tap "Connect" and you're done. The whole thing takes about 30 seconds.

If that automatic screen doesn't appear, your device didn't detect the case. This usually means the case is too far away (try moving closer), or Bluetooth is turned off on your phone. Check your device's Settings > Bluetooth and make sure it's on.

Key Takeaways

  • New AirPods come pre-paired to each other; you only need to pair the case to your phone by opening the lid nearby and tapping Connect.
  • If the setup screen doesn't appear, move the case closer to your device and confirm Bluetooth is turned on in Settings.
  • You can pair the same AirPods to multiple devices (iPhone, iPad, Mac, Apple Watch), and they'll switch automatically when you use each device.
  • If pairing fails or the AirPods don't show up in Bluetooth settings, reset the case by holding the button on the back for 15 seconds until the light flashes amber.

What to do if the automatic setup screen doesn't appear

Sometimes the setup prompt doesn't pop up on your screen even though the case is nearby. The most common reason is that Bluetooth is off. Go to Settings > Bluetooth on your iPhone or iPad and toggle it on. Wait a few seconds, then open the AirPods case again near your device.

If Bluetooth is already on and nothing happens, try moving the case within a few inches of your phone. Bluetooth range is usually 30 feet in open space, but walls and other devices can interfere. Once the setup screen appears, tap the device name (usually "Your Name's AirPods") and then tap "Connect."

If you still don't see the setup screen after trying these steps, your AirPods may need a reset. See the reset section below.

Pairing the same AirPods to a second device (Mac, iPad, or Apple Watch)

Once your AirPods are paired to your iPhone, you can add them to other Apple devices without unpairing from the first one. On your Mac, go to System Settings > Bluetooth, then look for your AirPods in the list and click "Connect." On an iPad, use Settings > Bluetooth and do the same. On an Apple Watch, open the Watch app on your paired iPhone, go to Bluetooth, and select your AirPods.

After you've paired to multiple devices, your AirPods will automatically switch to whichever device you're actively using—if you start playing audio on your Mac, they'll disconnect from your iPhone and connect to the Mac instead. You can also manually switch by opening Control Center on any of your devices and tapping the audio output menu.

How to reset AirPods if pairing fails

If your AirPods won't pair to any device, a reset usually fixes it. First, forget the AirPods from your phone: go to Settings > Bluetooth, find your AirPods in the list, tap the info icon next to them, and select "Forget This Device." Do this on any device where they're currently paired.

Next, hold the small button on the back of the charging case for about 15 seconds. You'll see the light on the front of the case flash amber, then white. This means the AirPods have been reset and are ready to pair again. Now open the case near your iPhone and follow the initial setup process.

If the light doesn't flash after 15 seconds, make sure the AirPods are actually inside the case and the case has a charge. A completely dead case won't reset. Plug it in for at least 15 minutes, then try again.

Why your AirPods might not stay paired

If your AirPods pair successfully but then disconnect randomly, the problem is usually interference or a weak Bluetooth connection rather than a pairing issue. Move closer to your device and away from other electronics like microwaves or Wi-Fi routers, which can disrupt Bluetooth signals on the 2.4 GHz frequency.

Another common cause is that your device's Bluetooth has crashed. Toggle Bluetooth off in Settings, wait 10 seconds, then turn it back on. Your AirPods should reconnect automatically. If they don't, forget them and pair again using the reset steps above.

If one AirPod keeps disconnecting while the other stays connected, that earbud may have a low battery. Put both AirPods back in the case for at least 15 minutes to charge, then take them out and use them again.

Pairing AirPods to non-Apple devices (Android, Windows, or older Bluetooth speakers)

AirPods work with any device that supports Bluetooth, not just iPhones and Macs. To pair to an Android phone, put your AirPods in the case, hold the button on the back for about 15 seconds until the light flashes white (not amber), then release. The AirPods are now in pairing mode.

On your Android device, go to Settings > Bluetooth and look for your AirPods in the available devices list. Tap them to pair. The process is the same for Windows computers or any other Bluetooth device—put the AirPods in pairing mode, then search for them in that device's Bluetooth settings and select them.

One important note: when you pair AirPods to a non-Apple device, they won't automatically switch between devices the way they do with iPhones and Macs. You'll need to manually disconnect from one device and connect to another in Bluetooth settings each time you switch.

Frequently Asked Questions

Do I need to unpair my AirPods from my old phone before pairing them to a new one?

Not strictly, but it's a good idea. If you don't forget them on your old phone, they may try to reconnect to it when Bluetooth is on. Go to Settings > Bluetooth on your old device, find the AirPods, tap the info icon, and select "Forget This Device." Then pair them to your new phone the normal way.

Why does the setup screen say "Unable to set up" when I try to pair?

This usually means your device's Bluetooth is having trouble communicating with the case. Try restarting your phone (power it off completely, wait 10 seconds, then power it back on), then open the AirPods case near it again. If that doesn't work, reset the AirPods using the button on the back of the case.

Can I pair my AirPods to my Apple Watch without an iPhone?

No. Apple Watch requires an iPhone to set up and manage AirPods pairing. You need to pair the AirPods to your iPhone first, then add them to your Watch through the Watch app on your iPhone.

What if I lost one AirPod—can I pair a replacement to my case?

You'll need to buy a replacement earbud from Apple, not a whole new pair. When you get it, put it in the case with your remaining original AirPod and hold the reset button on the back for 15 seconds. The new earbud will pair to the case and to your devices automatically.