The DJI Mic 2 pairs to its receiver through a single button press on both devices

The DJI Mic 2 wireless microphone system uses a pairing process that takes about 10 seconds and requires no app or computer. You hold the pairing button on the transmitter (the microphone itself) and the receiver at the same time until both devices flash in sync, then release. After that, they remember each other and reconnect automatically whenever both are powered on.

The receiver is the small box that connects to your camera, phone, or audio interface. The transmitter is the clip-on microphone you wear or place near your sound source. Both come pre-paired from the factory, so if you are using the original receiver that came in your box, you may not need to pair them again. You only pair them if you are replacing one device, using a second receiver, or the connection has been lost.

Key Takeaways

  • Press and hold the pairing button on both the transmitter and receiver simultaneously until the LED lights flash in unison, which takes about 10 seconds.
  • The pairing button on the transmitter is located on the bottom of the device; on the receiver, it is a small recessed button on the side or back.
  • Once paired, the devices connect automatically when powered on and do not need to be re-paired unless you replace a device or manually reset them.
  • If pairing fails, power both devices off, wait 10 seconds, power them back on, and try again.

Locating the pairing buttons on both devices

The transmitter's pairing button is on the bottom of the microphone unit. It is a small recessed button that you press with a fingernail or the tip of a pen. You do not need to remove the battery or open any panels to access it.

The receiver's pairing button is on the side or back of the unit, depending on which version you have. It is also recessed and small. If you cannot find it when ready, look for a button labeled with a pairing symbol (usually two connected dots or a link icon) or check the quick-start guide that came in your box. The manual will show you exactly where it is on your specific model.

Step-by-step pairing instructions

Power on both the transmitter and receiver. Wait for them to fully boot—you will see the LED lights turn on. This usually takes 3 to 5 seconds.

Press and hold the pairing button on the transmitter with one hand. While holding it, press and hold the pairing button on the receiver with your other hand. Keep both buttons pressed. The LED lights on both devices will begin to flash. Continue holding until the flashing becomes synchronized—both lights flash at the same time in the same color. This synchronization is your signal that pairing is complete.

Release both buttons. The lights should now be solid or flash in a steady pattern that indicates a connected state. The devices are now paired and will remember each other.

What the LED lights tell you during pairing

Before pairing begins, the transmitter and receiver each have their own LED pattern. The transmitter typically shows a slow pulse or blink, and the receiver does the same. These independent patterns mean they are not yet talking to each other.

When you press the pairing buttons, the lights will start flashing faster and more erratically as the devices search for each other. Once they find each other, the flashing becomes synchronized—both lights flash together in the same color and rhythm. This is the moment you can release the buttons. After release, the lights settle into a solid color or a slow, steady pulse, which means the connection is active and stable.

If the lights never synchronize and you release the buttons after 15 to 20 seconds, the pairing has failed. Power both devices off, wait 10 seconds, and try again.

Reconnecting after powering off and on

Once paired, the DJI Mic 2 transmitter and receiver do not need to be re-paired every time you use them. When you power on the receiver first, it will search for the transmitter. When you power on the transmitter within about 30 seconds, it will find the receiver and connect automatically. The LED lights will show a solid or steady-pulse pattern once connected.

If you power on the transmitter but the receiver is off, the transmitter will wait in pairing mode for up to 5 minutes. If you then power on the receiver, they will connect. If more than 5 minutes pass, power the transmitter off and back on to reset its search.

Resetting the pairing if the connection is lost

If the transmitter and receiver stop connecting even though they were previously paired, a reset usually fixes it. Power off both devices completely. Wait at least 10 seconds. Power on the receiver first, then power on the transmitter. They should reconnect automatically within 10 seconds.

If automatic reconnection does not happen, repeat the full pairing process from the beginning. Hold the pairing buttons on both devices simultaneously until the LED lights synchronize, then release. This re-establishes the pairing and usually resolves connection drops caused by interference or a temporary loss of signal.

Pairing a second receiver to the same transmitter

The DJI Mic 2 transmitter can be paired to multiple receivers, though only one receiver can be active at a time. To pair a second receiver, power on the new receiver and the transmitter. Press and hold the pairing button on both the transmitter and the new receiver until the LED lights synchronize. Release the buttons. The transmitter now remembers both receivers.

When you want to switch between receivers, power off the first receiver and power on the second. The transmitter will automatically connect to whichever receiver is on. If both receivers are powered on at the same time, the transmitter will connect to the one it paired with most recently.

Frequently Asked Questions

What if the pairing button is stuck or does not respond?

The pairing button is recessed to prevent accidental presses. If it feels stuck, try pressing it with a straightened paperclip or a ballpoint pen instead of your fingernail. explore steady pressure rather than jabbing. If it still does not respond, the device may have a hardware fault and should be checked by DJI support.

Can I pair the transmitter to a receiver from a different DJI Mic model?

No. The DJI Mic 2 transmitter only pairs with DJI Mic 2 receivers. It is not compatible with the original DJI Mic or other DJI wireless systems. If you have mixed models, you will need matching transmitters and receivers for each system.

How far apart do the devices need to be when pairing?

They should be within 1 meter (about 3 feet) of each other during the pairing process. Pairing at a distance can fail because the devices need a strong signal to recognize each other. Once paired, they can operate at their normal range, which is up to 250 meters in open space.

Do I need to pair the devices every time I use them?

No. Once paired, the transmitter and receiver remember each other permanently until you manually reset them or pair one of them to a different device. straightforward power them on and they will connect automatically.

What should I do if the LED lights never synchronize during pairing?

Power both devices off, wait 10 seconds, and power them back on. Try the pairing process again, making sure you are pressing both buttons at exactly the same time and holding them for at least 10 seconds. If synchronization still does not occur, move the devices closer together and try once more. If the problem persists, contact DJI support.