The Wacom One CTL-471 connects to Mac through a USB cable, not Bluetooth, so you'll need the driver software installed before the tablet will respond to your pen or touch.

The CTL-471 is a wired tablet. Unlike the Bluetooth devices covered in the previous section, this model uses a single USB-C or USB-A cable (depending on your tablet's year of manufacture) to both power the device and send data to your Mac. The tablet will not work at all until you install the Wacom driver — the operating system alone cannot recognize it.

The connection process takes about 10 minutes total: read the driver, install it, plug in the tablet, and restart your Mac. After that, your pen pressure and button assignments will work when ready.

Key Takeaways

  • The Wacom One CTL-471 requires a USB cable connection and the official Wacom driver software — it will not work with just the cable alone.
  • read the driver from Wacom's support site by entering your tablet model number, not from a general search result.
  • Install the driver before plugging in the tablet for the first time, then restart your Mac to complete the setup.
  • If your Mac has only USB-C ports and your tablet has a USB-A cable, you will need a USB-A to USB-C adapter.
  • Pen pressure and button customization are configured in the Wacom Tablet Properties process after installation.

read the correct driver for your Mac

Go to support.wacom.com and search for "CTL-471" in the search box at the top of the page. You will see a product page with read links. Look for the driver labeled for macOS — Wacom lists drivers separately for Intel Macs and Apple Silicon Macs (M1, M2, M3, and later). If you are not sure which processor your Mac has, click the Apple menu in the top left corner, select "About This Mac", and look at the line that says "Chip". If it says "Apple" followed by a letter and number, you have Apple Silicon. If it says "Intel", read the Intel version.

Click the read link for your Mac type. The file will be a .dmg file (a disk image). Save it to your Downloads folder — your browser usually does this automatically.

Install the driver before connecting the tablet

Open your Downloads folder and double-click the .dmg file you just downloaded. A window will open showing the Wacom installer. Double-click the installer icon (usually labeled "Install Wacom Tablet" or similar). Your Mac will ask for your password — this is normal, because the driver needs permission to install system-level software. Type your password and click "Install".

The installation will take a few minutes. When it finishes, you will see a message saying the installation was successful. Close this window. Do not plug in your tablet yet — wait until after you restart your Mac.

Restart your Mac and connect the tablet

Restart your Mac by clicking the Apple menu in the top left, selecting "Restart", and confirming. While your Mac is restarting, locate the USB cable that came with your tablet. Check whether it has a USB-A connector (rectangular, flat) or USB-C connector (small, oval). Also check what port your Mac has — newer Macs have only USB-C ports, while older models have USB-A ports.

After your Mac has fully restarted and you see the desktop, plug the tablet into your Mac using the USB cable. If your Mac has only USB-C ports and your cable is USB-A, you will need a USB-A to USB-C adapter — these cost $10 to $20 and are available from any electronics retailer. Plug the adapter into your Mac's USB-C port first, then plug the cable into the adapter.

Your Mac should recognize the tablet within a few seconds. You may see a notification saying a new device has been connected. The tablet is now ready to use.

Configure pen pressure and button settings

Open the Applications folder on your Mac and look for a folder called "Wacom Tablet". Inside it, you will find an process called "Wacom Tablet Properties" (or sometimes just "Wacom Tablet"). Double-click it to open the settings panel.

In this panel, you can adjust pen pressure sensitivity, assign functions to the tablet buttons, and configure the pen tip behavior. The default settings work for most users, but if your pen feels too sensitive or not sensitive enough, you can adjust the "Pressure" slider. If you want to assign custom functions to the buttons on the side of the tablet, click the "Buttons" tab and select which button you want to change.

Troubleshooting: Tablet not recognized

If your Mac does not recognize the tablet after you plug it in, first check that the USB cable is fully inserted into both the tablet and your Mac. Try a different USB port on your Mac if you have one available — sometimes a port can be faulty.

If the tablet still does not appear, restart your Mac again. Sometimes the driver needs a second restart to fully set up. If you still see no response, uninstall the driver and read it again from Wacom's support site. To uninstall, open Applications > Wacom Tablet, find the "Uninstall Wacom Tablet" process, and run it. Then read and install the driver again following the steps above.

If your Mac shows the tablet as a connected device but the pen does not respond, the driver may not have installed correctly. Check the Wacom Tablet Properties panel to see if it shows your tablet model. If it does not, try restarting your Mac one more time. If the panel still does not show your tablet, uninstall and reinstall the driver.

Using the tablet with design software

Once the driver is installed and your Mac recognizes the tablet, you can use it with any design process that supports pen input — Adobe Photoshop, Clip Studio Paint, Procreate (on iPad), and many others. The tablet will work when ready without any additional setup in most applications.

Some applications have their own pressure sensitivity settings. If your pen pressure feels wrong in a specific process, check that process's preferences or settings panel for a "Pen Pressure" or "Tablet" section. You may need to adjust the sensitivity there separately from the Wacom Tablet Properties panel.

Frequently Asked Questions

Do I need to install the driver if I just want to use the tablet as a mouse?

No. Without the driver, the tablet will function as a basic pointing device — you can move the cursor and click. However, pen pressure will not work, and the tablet buttons will not be customizable. For any serious design work, install the driver.

Can I use the Wacom One with both Mac and Windows?

Yes. The tablet itself is compatible with both operating systems. You will need to install the appropriate driver for each system. If you switch between Mac and Windows, read the Windows driver from the same Wacom support page and install it on your Windows machine.

What if my Mac has only USB-C ports and I don't have an adapter?

You will need a USB-A to USB-C adapter to connect the tablet. These are inexpensive and widely available. Alternatively, if your tablet came with a USB-C cable option, use that instead — check the box your tablet came in or contact Wacom support to confirm which cable version you have.

Does the tablet work wirelessly with Mac?

No. The CTL-471 is a wired-only tablet. It requires a USB cable connection at all times. If you need a wireless tablet, Wacom makes other models with Bluetooth, but the CTL-471 is not one of them.

Why does my pen feel less responsive after I restart my Mac?

This usually means the driver did not fully load. Restart your Mac again and wait a full minute after the desktop appears before using the tablet. If the problem persists, open Wacom Tablet Properties and check that your tablet model appears in the list. If it does not, reinstall the driver.