The basic connection process
To connect a device to your Beats Pill, turn on the speaker, hold down the power button until the LED light flashes (usually 3 to 5 seconds), then open your device's Bluetooth settings and select "Beats Pill" from the list. The first time you connect, the pairing happens automatically once you select it. After that, your device will remember the Beats Pill and reconnect when both are powered on and in range.
The whole process takes less than a minute. Once connected, audio from your phone, tablet, or computer will play through the speaker without any cables.
Key Takeaways
- Put the Beats Pill into pairing mode by holding the power button until the light flashes, which signals it is ready to connect.
- Your device's Bluetooth settings will show "Beats Pill" in the available devices list once pairing mode is active.
- After the first connection, your device automatically reconnects to the Beats Pill when both are turned on and within Bluetooth range (typically 30 feet).
- If connection fails, restart both the speaker and your device, then repeat the pairing process from the beginning.
- Only one device can play audio through the Beats Pill at a time, though you can pair multiple devices — you just switch which one is active.
Finding the power button and pairing light
The power button on a Beats Pill is located on the top of the speaker, usually near the center. Press it once to turn the speaker on; you will hear a startup sound and see a white LED light. To enter pairing mode, hold that same button down for about 3 to 5 seconds. The light will begin flashing, which means the speaker is now discoverable and waiting for a connection.
If the light does not flash, the speaker may already be paired to another device. In that case, hold the power button for 10 seconds to reset the pairing and start over. The light should flash after the reset.
Connecting on iPhone or iPad
Open Settings, tap Bluetooth, and make sure Bluetooth is turned on. Wait a moment for your device to scan for nearby speakers. When you see "Beats Pill" appear in the list under "Other Devices," tap it. Your iPhone or iPad will connect automatically, and you will see a checkmark next to "Beats Pill" once the pairing is complete.
If you do not see "Beats Pill" in the list, go back to the speaker and hold the power button again until the light flashes. Then return to your phone's Bluetooth settings and try again. Sometimes the speaker needs a few seconds to become visible.
Connecting on Android devices
Open Settings, go to Bluetooth, and turn it on if it is not already active. Your Android phone or tablet will begin scanning for nearby devices. When "Beats Pill" appears in the list of available devices, tap it to connect. You may see a pairing request pop up on your screen — if so, tap "Pair" to confirm.
Android devices sometimes take longer to discover Bluetooth speakers than iPhones do. If "Beats Pill" does not show up after 30 seconds, restart Bluetooth on your phone by toggling it off and back on, then check the list again.
Connecting on Windows or Mac computers
On a Mac, click the Bluetooth icon in the menu bar at the top of the screen, then select "Beats Pill" from the list. On Windows 10 or 11, go to Settings, click Devices, select Bluetooth, and look for "Beats Pill" in the available devices. Click or tap it to connect.
Computers sometimes require you to confirm the pairing on both the speaker and the computer itself. If a dialog box appears asking you to confirm, click "Pair" or "Connect." Once connected, the Beats Pill will appear in your audio output options, and you can select it to route sound through the speaker.
What to do if the connection fails
If your device does not find the Beats Pill, or if the connection drops, start by restarting both devices. Turn off the speaker completely, wait 10 seconds, then turn it back on. At the same time, turn off Bluetooth on your phone or computer, wait a few seconds, and turn it back on. Then put the Beats Pill into pairing mode again by holding the power button until the light flashes.
If the speaker still does not appear, check that Bluetooth is actually enabled on your device — sometimes it is turned off without you realizing it. Also make sure you are within 30 feet of the speaker; Bluetooth has a limited range, and walls or other obstacles can weaken the signal. If you are far away or in a different room, move closer and try again.
If the Beats Pill was previously paired to a different device, it may try to reconnect to that device instead of accepting a new pairing. Hold the power button for 10 seconds to fully reset the speaker's pairing memory, then start the connection process from the beginning.
Switching between multiple paired devices
You can pair the Beats Pill to several different phones, tablets, or computers, but only one device can play audio at a time. To switch from one device to another, straightforward stop playing audio on the first device and start playing on the second. The speaker will automatically switch to whichever device is actively sending sound.
If you want to force a switch without playing audio, you can disconnect the Beats Pill from the first device in its Bluetooth settings, then reconnect it to the second device. This is useful if the speaker keeps trying to reconnect to a device you are no longer using.
Frequently Asked Questions
Why does my Beats Pill keep disconnecting?
Disconnections usually happen when your device moves out of Bluetooth range, when another device tries to connect, or when the speaker's battery is very low. Try moving closer to the speaker and make sure no other devices are attempting to pair. If the battery is below 20 percent, charge the speaker and try again.
Can I use the Beats Pill with two devices at the same time?
No. Only one device can send audio to the speaker at a time. If two devices are paired, whichever one is actively playing will take over. You have to stop audio on one device before the other can use the speaker.
What if I forgot which device the Beats Pill is currently paired to?
Hold the power button for 10 seconds to reset all pairings. The speaker will return to factory settings, and the LED light will flash. Then you can pair it to any device as if it were brand new.
Does the Beats Pill need to be charged before I can pair it?
The speaker needs enough battery to power on and enter pairing mode, but it does not need to be fully charged. If the battery is completely dead, charge it for at least 15 minutes before attempting to connect.
Why does my computer not show the Beats Pill in its Bluetooth list?
Some computers have Bluetooth disabled by default or turned off in the BIOS. Check your computer's Bluetooth settings to make sure Bluetooth is turned on. On Windows, also check that your Bluetooth drivers are up to date. On Mac, restart your computer if the speaker does not appear after several attempts.