The basic steps to pair your Pro Controller
To connect a Pro Controller to your Switch, you need to put the controller in pairing mode, then tell the Switch to look for it. The whole process takes about two minutes and works the same way whether you are setting up a new controller or reconnecting one you have used before.
Start by pressing the small pairing button on the top of the Pro Controller — it is the round button between the USB-C port and the headphone jack. Hold it for three seconds until the lights on the controller start flashing. This puts the controller in pairing mode, meaning it is broadcasting a signal that your Switch can hear.
On your Switch, go to System Settings, then Controllers and Sensors, then Change Grip/Order. The Switch will now search for controllers in pairing mode. When your Pro Controller appears on the screen, select it. The lights will stop flashing and stay solid, which means the pairing is complete.
Key Takeaways
- Press and hold the pairing button on top of the Pro Controller for three seconds until the lights flash.
- On your Switch, open System Settings, go to Controllers and Sensors, then select Change Grip/Order to find the controller.
- The connection uses Bluetooth, so keep the controller within 30 feet of the Switch while pairing.
- Once paired, the Pro Controller will reconnect automatically the next time you turn it on, as long as the Switch is nearby.
Why the pairing button matters
The pairing button exists because Bluetooth devices need a way to know which device is trying to connect to them. Without it, any Pro Controller in range could connect to your Switch, and you would have no control over which one. By pressing the button, you are telling that specific controller "announce yourself now" for a short window of time.
If you do not see the lights flash after pressing the button, the controller battery may be dead. Plug it into a USB-C cable and wait a few minutes before trying again. The lights should flash within three seconds of pressing the button if the battery has any charge.
What to do if the controller does not appear on the Switch
If you held the pairing button but the controller does not show up in the Change Grip/Order menu, the most common cause is that the Switch did not start searching in time. Go back to Change Grip/Order and try again, this time pressing the pairing button right after you see the search screen appear.
If the controller still does not appear, try restarting both devices. Turn off the Switch completely, then turn it back on. While it is starting up, press the pairing button on the Pro Controller. This gives the Switch a fresh chance to find the controller as it boots.
If you have already paired this controller to the Switch before and it is not showing up now, the issue may be that it is still trying to connect to a different device — another Switch, a PC, or a phone. Turn off Bluetooth on any other devices nearby, then try pairing again.
How the Pro Controller stays connected after pairing
Once you have paired the controller, the Switch remembers it. The next time you turn on the Pro Controller by pressing any button, it will automatically search for your Switch using Bluetooth. If your Switch is on and nearby, the connection happens in a few seconds without you doing anything.
The Switch can remember up to ten controllers at once. If you pair a second or third Pro Controller, each one will reconnect on its own when you press a button. This is why the pairing button only needs to be used once per controller — after that, the devices know each other.
Troubleshooting a controller that was working but stopped connecting
If a Pro Controller that you have used before suddenly will not connect, the first step is to check the battery. A controller with very low battery may not have enough power to broadcast its Bluetooth signal strongly. Plug it in and let it charge for at least 15 minutes, then try turning it on again.
If the battery is not the problem, try "forgetting" the controller on the Switch and pairing it again from scratch. Go to System Settings, Controllers and Sensors, then Disconnect Controllers. Select the Pro Controller you want to forget, then confirm. After that, use the pairing button method described above to reconnect it.
In rare cases, the Bluetooth chip inside the controller or Switch can develop a fault. If you have tried charging, restarting, and re-pairing and the controller still will not connect, the hardware may need repair or replacement.
Using a Pro Controller with multiple Switch consoles
A single Pro Controller can be paired to more than one Switch. You do not need to unpair it from your first Switch to use it on a second one — just press the pairing button when you are near the second Switch and follow the same steps. The controller will remember both Switches.
When you turn on the controller near either Switch, it will connect to whichever one is closest or turned on. If both Switches are on and nearby, the controller may connect to the one it paired with most recently. If you want to make sure it connects to a specific Switch, turn off the other one first.
Wired connection as an alternative
If you want to use the Pro Controller without Bluetooth, you can plug it directly into the Switch's USB-C port with a USB-C cable. This bypasses pairing entirely — the Switch will recognize the controller as soon as the cable is connected. Wired mode is useful if Bluetooth is not working or if you want a may provide stable connection.
Wired connection does not require any setup. Just plug in the cable and start playing. The controller will charge while it is plugged in, and you can use it while charging without any delay.
Frequently Asked Questions
Do I have to pair my Pro Controller every time I use it?
No. Once you pair it the first time, the Switch remembers it. Every time you turn on the controller after that, it will reconnect automatically as long as the Switch is on and nearby. You only use the pairing button once, when setting up a new controller or after forgetting it.
Can I use a Pro Controller on a Switch Lite?
Yes, but only wirelessly. The Switch Lite does not have a USB-C port on the dock, so you cannot use a wired connection. Pair the Pro Controller using the pairing button method, and it will work the same way as on a full-size Switch.
What if the pairing button is stuck or broken?
If the button will not press or feels damaged, you can still pair the controller by plugging it into the Switch with a USB-C cable. Once it is connected by wire, go to Change Grip/Order and the Switch will recognize it. After that, you can unplug it and use it wirelessly without ever pressing the pairing button again.
How far away can the Pro Controller be from the Switch?
Bluetooth typically works within 30 feet in an open space. Walls and other obstacles can reduce that range. If your controller keeps disconnecting, try moving closer to the Switch or removing obstacles between them. If you are far away and the connection drops, move back into range and press any button on the controller to reconnect.
Can I pair a Pro Controller to my phone or computer instead?
Yes. The Pro Controller uses standard Bluetooth, so it can pair with any device that supports Bluetooth controllers — phones, tablets, PCs, and Macs. Use the same pairing button method: press and hold it for three seconds, then search for the controller in your device's Bluetooth settings. Keep in mind that once it is paired to another device, it may try to connect there instead of your Switch.