The basic steps to pair your mouse

Turn on your Bluetooth mouse and make sure it is in pairing mode. Most mice have a small button on the bottom or side — hold it for three to five seconds until you see a light blink or flash. Some mice turn on pairing mode automatically the first time you switch them on.

On your Mac, open System Settings (or System Preferences on older versions). Click Bluetooth in the left sidebar. Your mouse should appear in the list of available devices within a few seconds. Click it, then click Connect. Your Mac will pair with the mouse and remember it — the next time you turn the mouse on, it will reconnect without needing to pair again.

If your mouse does not appear in the Bluetooth list, make sure it is actually in pairing mode. Some mice only stay in pairing mode for 30 seconds, so you may need to hold the button again. If the mouse still does not show up, try restarting your Mac's Bluetooth: toggle Bluetooth off and on again in System Settings.

Key Takeaways

  • Put your mouse in pairing mode by holding the button on the bottom or side until the light blinks, then open Bluetooth in System Settings and click the mouse name.
  • Your Mac remembers the mouse after the first pairing, so it will reconnect automatically each time you turn it on.
  • If the mouse does not appear in the Bluetooth list, check that pairing mode is still active — many mice only stay in pairing mode for 30 seconds.
  • Restarting your Mac's Bluetooth by toggling it off and on again fixes most connection problems.

Where to find the pairing button on your mouse

The pairing button location varies by mouse model. On most wireless mice, it is on the bottom near the battery compartment or on the side near the thumb rest. Look for a small recessed button, sometimes labeled with a Bluetooth symbol or the word "Pair". You may need a pen or paperclip to press it if it is recessed.

Some newer mice, especially Apple's Magic Mouse, do not have a separate pairing button. Instead, they enter pairing mode automatically when you turn them on for the first time, or when the battery is very low. Check your mouse manual or the manufacturer's website if you cannot find a button — the model number is usually printed on the bottom.

What to do if your mouse will not appear in Bluetooth settings

First, confirm the mouse is actually powered on. Check the battery level by looking for a light on the mouse itself, or by checking the battery indicator in System Settings under Bluetooth — if the mouse is already paired, it will show the battery percentage there. A dead battery is the most common reason a mouse stops connecting.

If the battery is good, restart your Mac's Bluetooth. Open System Settings, click Bluetooth, and toggle it off. Wait five seconds, then toggle it back on. This resets the Bluetooth radio and often fixes connection problems. If the mouse still does not appear, try restarting your Mac entirely — shut it down completely, wait 30 seconds, and turn it back on.

If you have already paired this mouse to your Mac before, it may be trying to reconnect to an old pairing instead of entering pairing mode. Forget the mouse first: in System Settings under Bluetooth, find the mouse name, click the X or "Remove" button next to it, then put the mouse back into pairing mode and pair it again.

Connecting multiple mice to the same Mac

Your Mac can pair with multiple Bluetooth mice at the same time, though only one will work as the active cursor at any given moment. Pair each mouse the same way: put it in pairing mode, open Bluetooth in System Settings, and click its name. All paired mice will appear in your Bluetooth list.

To switch between mice, straightforward move or click the one you want to use. Your Mac will automatically make it the active device. This is useful if you have a mouse at your desk and a trackpad in your bag, or if you share a Mac with someone else who has their own mouse.

Fixing a mouse that connects but does not work properly

If your mouse connects but the cursor moves slowly, jumps around, or does not respond to clicks, the problem is usually interference or a low battery. Check the battery level in System Settings under Bluetooth — if it is below 20 percent, replace or charge the batteries. Low battery causes erratic behavior before the mouse stops connecting entirely.

Interference from other wireless devices can also cause problems. Move your mouse closer to your Mac, and move other wireless devices (like a router or cordless phone) farther away. If you have many Bluetooth devices paired, try disconnecting the ones you are not using — too many active devices can cause the mouse to lag.

If the cursor still behaves oddly, forget the mouse and pair it again. Open System Settings, click Bluetooth, find the mouse, click the X next to it, then put the mouse back into pairing mode and reconnect. A fresh pairing often fixes responsiveness problems that a straightforward restart does not.

Why your mouse disconnects and reconnects

Occasional disconnects usually mean the battery is low. Your Mac will try to reconnect automatically, which is why you see the cursor freeze briefly. Replace or charge the batteries — this solves the problem in most cases.

If disconnects happen frequently even with a fresh battery, the mouse may be too far from your Mac. Bluetooth has a range of about 30 feet in open space, but walls and metal objects reduce it. Keep your mouse within 10 feet of your Mac, especially if you have walls or cabinets between them.

Persistent disconnects can also mean the pairing itself is corrupted. Forget the mouse in System Settings, restart your Mac, then pair the mouse again from scratch. This clears out any old connection data that might be causing problems.

Frequently Asked Questions

Do I need to pair my mouse every time I turn on my Mac?

No. Once you pair a mouse, your Mac remembers it permanently. The next time you turn the mouse on, it will reconnect automatically without any action from you. You only need to pair once, unless you forget the mouse in System Settings or pair it to a different Mac.

Can I use a Bluetooth mouse from a different brand with my Mac?

Yes. Any Bluetooth mouse will work with any Mac, regardless of brand. Apple mice work with Macs, but so do mice from Logitech, Microsoft, Razer, and other manufacturers. The pairing process is the same for all of them.

What if my Mac does not have Bluetooth?

All modern Macs have Bluetooth built in. If your Mac is very old (pre-2008), it may not have Bluetooth, but you can add it with a USB Bluetooth adapter. Plug the adapter into a USB port, then pair your mouse the same way. Older Macs may need a driver from the mouse manufacturer.

Why does my mouse work sometimes but not other times?

This almost always means the battery is low or dying. Even if the battery indicator shows some charge, old batteries can become unreliable. Try new batteries first. If the problem continues, forget the mouse and pair it again — corrupted pairing data can cause intermittent connection problems.

Can I pair a mouse that uses a USB receiver instead of Bluetooth?

No, not through Bluetooth. Mice with USB receivers use a different wireless technology and must be plugged into a USB port. They do not appear in Bluetooth settings. Check your mouse documentation to see whether it uses Bluetooth or a USB receiver — Bluetooth mice have no receiver to plug in.