The basic connection process
Your Apple Pencil connects to your iPad through Bluetooth, the same wireless standard you learned about in the pairing guide. The connection happens automatically the first time you bring a new Apple Pencil close to an iPad — you do not need to hunt through settings or type in codes. Depending on which Apple Pencil model you own, the physical setup differs slightly, but the result is the same: your iPad recognizes the pencil and remembers it.
The first step is to check which Apple Pencil model you have. Apple makes three versions: the original Apple Pencil (with a removable cap), Apple Pencil (2nd generation, with a flat edge), and Apple Pencil Pro (the newest model with a squeeze gesture). Each one pairs differently because they charge differently. Knowing your model before you start saves time and prevents confusion.
Key Takeaways
- Apple Pencil pairs automatically when you bring it close to an iPad for the first time — no manual pairing steps are needed.
- The original Apple Pencil requires you to remove the cap and plug it into the iPad's Lightning port to start pairing.
- Apple Pencil (2nd generation) pairs when you attach it magnetically to the side of the iPad, which also charges it.
- After the first pairing, your Apple Pencil reconnects automatically whenever you use it near the same iPad.
- If your pencil does not pair, restarting both the iPad and the pencil (by charging it fully) usually solves the problem.
Pairing the original Apple Pencil
The original Apple Pencil has a removable cap on one end and a Lightning connector underneath. To pair it, remove the cap by twisting it counterclockwise. You will see the Lightning connector — this is the small metal plug that looks like a flattened rectangle.
Plug the Lightning connector into the iPad's Lightning port (the charging port at the bottom of most older iPads). Hold it there for a few seconds. Your iPad screen will show a popup asking if you want to pair the Apple Pencil. Tap "Pair" on that popup. The connection is now complete. You can unplug the pencil and start using it when ready.
The original Apple Pencil charges through this same Lightning port. You will need to plug it in regularly — it does not charge wirelessly or magnetically. If your pencil stops responding during use, it has likely run out of battery. Plug it back in for a few minutes to restore power.
Pairing Apple Pencil (2nd generation)
The 2nd generation Apple Pencil looks different: it has a flat edge running along one side instead of being round. This flat edge is magnetic. To pair it, hold the pencil so the flat edge faces the flat edge of your iPad, then slide the pencil onto the side of the iPad. It will snap into place magnetically and stay attached.
Your iPad screen will show a pairing popup within a few seconds. Tap "Pair" to confirm. The pencil is now connected. The magnetic attachment also charges the pencil automatically — you do not need to plug anything in. As long as the pencil is attached to the side of your iPad, it is charging.
If the popup does not appear after 10 seconds, make sure the flat edge of the pencil is aligned with the flat edge of the iPad. The magnets need to be in contact. If you are still not seeing the popup, try restarting your iPad by holding down the power button, sliding to power off, waiting 10 seconds, and turning it back on.
Pairing Apple Pencil Pro
Apple Pencil Pro is the newest model and pairs the same way as the 2nd generation: magnetically to the flat edge of your iPad. Attach the pencil to the side of your iPad by aligning the flat edges and letting the magnets pull them together. Your iPad will show a pairing popup within a few seconds.
Tap "Pair" on the popup. The connection is complete, and the pencil begins charging when ready. Apple Pencil Pro has additional features like squeeze gestures and haptic feedback, but these work automatically once pairing is done — you do not need to configure them separately.
What to do if pairing fails
If your Apple Pencil does not show a pairing popup after you plug it in or attach it magnetically, the most common cause is a low or dead battery. Charge the pencil fully before trying again. For the original Apple Pencil, plug it into the iPad for at least five minutes. For 2nd generation and Pro models, leave them attached magnetically to the iPad for at least 15 minutes.
If the pencil still does not pair after charging, restart your iPad. Press and hold the power button until you see the "slide to power off" screen, then slide to shut down. Wait 10 seconds, then press the power button again to turn the iPad back on. Try pairing the pencil again once the iPad has fully restarted.
If you are pairing a pencil that was previously connected to a different iPad, you may need to "forget" it from the old device first. Go to Settings on the old iPad, tap Bluetooth, find the Apple Pencil in the list, and tap the information icon next to it, then tap "Forget This Device". After that, the pencil should pair with your new iPad without trouble.
Reconnecting after the first pairing
Once your Apple Pencil has paired with your iPad once, it remembers that connection. The next time you bring the pencil close to the same iPad, it reconnects automatically — you do not need to repeat the pairing process. This happens in the background through Bluetooth, just like how your wireless headphones reconnect to your phone.
If your pencil is not responding when you try to use it, it has likely disconnected because the battery is low. Charge it using the method for your model (plug in for the original, or attach magnetically for 2nd generation and Pro). Once charged, it will reconnect automatically within a few seconds of being near the iPad.
Using your pencil with multiple iPads
One Apple Pencil can pair with multiple iPads, but it can only be actively connected to one at a time. If you pair your pencil with a second iPad, it will disconnect from the first one. You do not need to repeat the full pairing process — just bring the pencil close to the new iPad and it will reconnect to that device instead.
If you switch back to the original iPad, the pencil will reconnect to it automatically when you bring it close. The iPad remembers the pairing from before, so Bluetooth handles the reconnection without any action from you. This switching happens seamlessly and takes only a few seconds.
Frequently Asked Questions
Do I need to pair my Apple Pencil every time I use it?
No. After the first pairing, your Apple Pencil reconnects automatically whenever you bring it near your iPad. You only pair once, and the connection stays saved in your iPad's memory.
Can I use an Apple Pencil with any iPad?
No. The original Apple Pencil works with iPad (5th generation) and later, iPad Air 2 and later, and iPad mini 4 and later. Apple Pencil (2nd generation) and Pro require iPad Pro models from 2018 onward. Check your iPad model in Settings under General > About to confirm compatibility before purchasing a pencil.
What if my Apple Pencil pairs but does not draw on the screen?
First, make sure the app you are using supports Apple Pencil — not all apps do. If the app supports it, restart the app by closing it completely and opening it again. If drawing still does not work, restart your iPad. If the problem continues, the pencil tip may be worn out and need replacement, or the pencil itself may have a hardware issue.
Why does my Apple Pencil keep disconnecting?
The most common reason is a low battery. Charge your pencil fully and try again. If disconnections continue even after charging, restart your iPad. If the problem persists, try forgetting the pencil from Bluetooth settings and pairing it again from scratch.
Can I pair two Apple Pencils to the same iPad at the same time?
No. Only one Apple Pencil can be actively connected to an iPad at a time. If you pair a second pencil, the first one will disconnect. You can switch between pencils by bringing whichever one you want to use close to the iPad, and it will reconnect automatically.