A charger fails for one of five reasons: a broken cable, a damaged port on your device, a faulty power adapter, a tripped safety circuit, or a problem with the outlet itself

Most chargers stop working suddenly, but the failure almost never means you need a new device. The cable gets bent at the connector until the wires inside snap. The port fills with lint and dust. The adapter's internal components fail from heat or age. A safety feature cuts power when it detects a short circuit. Or the wall outlet straightforward has no power. Testing each one takes minutes and costs nothing.

Start by ruling out the outlet. Plug a lamp, phone charger, or any device you know works into the same outlet. If that device powers on, the outlet is fine and the problem is your charger or device. If nothing works in that outlet, try a different one in another room. If the second outlet works, the first one is dead — call an electrician or stop using it. If no outlets work, your home's power is down.

Key Takeaways

  • Test the outlet first by plugging in a device you know works; if that device powers on, your outlet is fine.
  • Inspect the cable for cracks, kinks, or exposed wires, especially near the connector where the cable bends most.
  • Clean the charging port on your device with a dry cotton swab or soft brush to remove lint and dust buildup.
  • Try a different charger of the same type on your device to determine whether the problem is the charger or the port.
  • If a different charger works, your original charger failed and needs replacement; if it does not work, your device port is damaged.

Examine the cable for visible damage

The cable is the weakest part of any charger. It bends hundreds of times, and the connector where it enters your device bears all the stress. Look along the entire length for cracks in the rubber coating, kinks that stay bent, or exposed copper wire. Pay special attention to the last six inches before the connector — this is where cables fail most often.

If you find a crack or exposed wire, the cable is unsafe and must be replaced. Do not wrap it in tape or try to repair it. A damaged cable can overheat, damage your device's port, or create a fire risk. If the cable looks intact but you suspect damage inside, try a different charger before replacing it.

Clean the charging port on your device

Lint, dust, and debris collect inside your device's charging port over months of use. This buildup prevents the charger connector from seating fully, breaking the electrical connection. The charger may feel loose, or it may not charge at all even when plugged in.

Turn off your device completely. Use a dry cotton swab, a soft-bristled toothbrush, or a wooden toothpick to gently brush or scrape inside the port. Work slowly and do not force anything. If lint comes out, keep going until no more appears. Do not use water, compressed air, or metal tools — water can damage internal components, compressed air can force debris deeper, and metal can short the port. After cleaning, wait five minutes before plugging in the charger.

Test with a different charger of the same type

Borrow a charger that matches your device's connector type — USB-C, Lightning, Micro-USB, or whatever your device uses. Plug it in and see whether your device charges. This single test tells you whether the problem is your charger or your device's port.

If the borrowed charger works, your original charger failed and needs replacement. Buy a new one from the device manufacturer or a reputable third-party maker that lists your device model on the packaging. If the borrowed charger does not work either, your device's charging port is damaged and needs professional repair. Contact the manufacturer or a repair shop that handles your device type.

Check whether the adapter itself is broken

The power adapter — the brick that plugs into the wall — can fail internally even if it looks fine. Feel it after it has been plugged in for a minute. It should be warm but not hot enough to hurt. If it is extremely hot, unplug it when ready and do not use it again.

Look at the adapter's cable connection point where it enters the brick. If it is cracked, loose, or the cable moves when you wiggle it gently, the adapter is damaged. Some adapters have a light that glows when power flows through them; if that light does not come on when you plug it in, the adapter is not receiving power or has failed internally. In any of these cases, replace the adapter.

Understand safety circuits and when they trip

Modern chargers have built-in safety features that cut power if they detect a short circuit, overheating, or a problem with your device's battery. When this happens, the charger stops working as a protection — it is not broken, it is doing its job.

If your charger suddenly stopped working after you spilled liquid on your device, exposed it to extreme heat, or dropped it hard, a safety circuit likely tripped. Unplug the charger and let your device dry completely for at least 24 hours in a warm, dry place. Do not try to charge it during this time. After drying, plug in the charger again. If it works, the safety circuit reset. If it does not work, your device has internal damage that needs professional repair.

Know when to replace versus repair

A damaged cable always means replacement — repair is not safe. A faulty power adapter also means replacement; adapters are inexpensive and widely available. A dirty charging port usually works again after cleaning and costs nothing.

A damaged charging port on your device is more expensive to fix. Contact the device manufacturer or search online for repair shops in your area that handle your device type. Get a quote before committing. Sometimes the repair cost is close to the cost of a used replacement device, so compare both options. If your device is very old, replacement may make more sense than repair.

Frequently Asked Questions

Can I use any charger with my device?

No. Your device requires a specific connector type and power level. Using the wrong charger can damage your battery or device. Check your device's manual or the manufacturer's website for the correct charger type. Third-party chargers work fine if they match your device's specifications, but always buy from reputable makers.

Why does my charger work sometimes but not always?

An intermittent charger usually means the cable is damaged inside or the connection is loose. Try wiggling the cable gently where it enters the connector — if charging starts and stops as you move it, the cable has a broken wire inside and needs replacement. If the port itself is loose, your device needs professional repair.

Is it safe to use a charger that gets very hot?

No. A charger that is too hot to touch safely is overheating and poses a fire risk. Unplug it when ready and do not use it again. Replace it with a new charger. Chargers should be warm but not painful to hold.

What should I do if liquid spilled on my charger?

Stop using it when ready. Unplug it from the wall and let it dry completely in a warm, dry place for at least 48 hours. Do not try to use it before it is fully dry. After drying, test it on a device you do not mind risking. If it works normally and does not get unusually hot, it is probably safe to use again.

Can I charge my device with a charger meant for a different device?

Only if the connector type and power output match exactly. Check your device manual or the charger packaging for the connector type and wattage. Using a charger with the wrong power output can damage your battery or device. When in doubt, use only the charger made for your device.