iPhone to iPhone wireless charging requires iOS 17 or later and specific hardware

Wireless power sharing — the ability to charge one iPhone from another — works only on iPhone 14, iPhone 15, and iPhone 16 models running iOS 17 or later. You place the phone you want to charge face-to-face with the phone providing power, with their screens about an inch apart. The charging phone detects the other device and begins transferring power wirelessly. This feature is sometimes called "reverse wireless charging" or "battery sharing."

The process is straightforward but has real limits. The phone providing power drains its own battery faster than normal charging, and the transfer rate is slow — typically adding 1 to 2 percent per minute to the receiving phone. It works best as an emergency top-up when you are away from a charger, not as a primary charging method.

Key Takeaways

  • Only iPhone 14, iPhone 15, and iPhone 16 models with iOS 17 or later can share power wirelessly with another iPhone.
  • Place the two phones face-to-face about an inch apart, with both screens facing the same direction, to start the transfer.
  • The charging phone must have at least 20 percent battery remaining to begin sharing, and it will drain quickly while doing so.
  • Wireless power sharing is slow and best used for emergency top-ups rather than full charges.
  • Cases, screen protectors, and metal objects between the phones will block or weaken the connection.

What you need to set up wireless charging between iPhones

Both phones must be iPhone 14 or newer and running iOS 17 or a later version. Check your iOS version by opening Settings, tapping General, then About. Look for the "Software Version" field. If either phone is running iOS 16 or earlier, wireless power sharing will not work.

The phone providing power needs at least 20 percent battery. If its battery is below that threshold, it will refuse to share power. This is a safety feature to prevent the donor phone from draining completely. The receiving phone can be at any battery level, including completely dead, though a completely dead phone may take a moment to respond to the charging signal.

Remove any thick cases, metal cases, or metal attachments from both phones. Wireless charging works through plastic and thin rubber, but metal blocks the signal entirely. Screen protectors usually do not interfere, but test yours first if you have trouble establishing a connection.

How to position the phones for wireless power transfer

Place the two phones face-to-face with their screens pointing in the same direction. The phones should be about one inch apart — close enough that they are nearly touching but with a small gap between them. The exact positioning matters because the charging coils are located in the center-back area of each phone.

Align the phones so their centers are roughly parallel to each other. If one phone is tilted at an angle or rotated sideways, the coils will not align and the transfer will not begin. Some people find it helpful to rest both phones against a small object — like a book or a phone stand — to hold them steady while charging.

Once you have the phones positioned correctly, the receiving phone will display a charging animation on its screen and emit a subtle vibration. The donor phone will show a battery icon indicating it is sharing power. If nothing happens after 10 seconds, adjust the phones slightly closer or check that both are running compatible iOS versions.

Why wireless power sharing is slow and when to use it

Wireless power transfer between iPhones adds roughly 1 to 2 percent battery per minute to the receiving phone. A full charge from 0 to 100 percent would take 50 to 100 minutes, which is why this feature is not practical for complete charging. In that same time, plugging into a wall charger would give you 80 to 100 percent battery.

The donor phone drains faster than it would during normal use because it is actively transmitting power while also running its own processes. You may notice the donor phone getting warm during the transfer, which is normal but means the battery is working harder. If the donor phone gets too hot, the transfer will pause automatically.

Use wireless power sharing when you need a quick emergency boost — perhaps 10 to 15 percent extra battery to reach a charger — rather than as your main charging method. It is most useful when you are traveling with someone else who has a compatible iPhone and both of you need to stretch your battery life until you find a power outlet.

Troubleshooting when wireless power sharing will not start

If the phones are positioned correctly but charging does not begin, check that both are running iOS 17 or later. Open Settings on each phone, go to General, then About, and confirm the software version. Even a phone running iOS 17.0 will work, but iOS 16 or earlier will not support power sharing.

Verify that the donor phone has at least 20 percent battery. If it is at 19 percent or lower, it will not share power. Charge the donor phone to at least 20 percent, then try again. Also check that neither phone is in Low Power Mode, which can prevent power sharing. Disable Low Power Mode in Settings under Battery, then attempt the transfer again.

Remove any cases, screen protectors with metal components, or metal rings or attachments. Even a thin metal plate under a case can block the wireless signal. Try the transfer with both phones completely bare. If it works without cases but not with them, your case is too thick or contains metal — consider a thinner case or one made entirely of plastic or silicone.

Make sure the phones are not too far apart and that their centers are aligned. Move them closer — they should be nearly touching with just a small gap. If one phone is tilted or rotated, straighten it so both screens face the same direction. Wait 10 to 15 seconds after positioning before assuming the connection has failed.

What happens to battery health when you use wireless power sharing

Wireless power sharing does not damage battery health any more than normal wireless charging does. The transfer is slow enough that it does not generate excessive heat, and Apple's software manages the power flow to prevent overcharging. Using this feature occasionally will not noticeably shorten your battery lifespan.

However, using it frequently — for example, charging one phone from another several times per day — will cause the donor phone's battery to cycle more often than usual. Battery cycles are the main factor in long-term battery wear. If you regularly share power, you may notice the donor phone's battery capacity declining slightly faster than it would otherwise.

For occasional emergency use, wireless power sharing is safe. For frequent charging, it is better to use a wall charger or portable battery pack, which are faster and do not drain another device's battery.

Alternatives when wireless power sharing is not available

If you have an older iPhone or one running iOS 16, wireless power sharing is not an option. A portable battery pack (also called a power bank) is the most practical alternative. These are small, inexpensive devices that hold a charge and can top up your phone multiple times. They work with any iPhone model and do not require another person's device.

If you are at home or in an office, a wall charger is always faster than wireless power sharing. Even a standard 5-watt charger will add battery much more quickly than the 1 to 2 percent per minute you get from phone-to-phone wireless transfer. If you are traveling, a portable battery pack is more reliable than hoping someone nearby has a compatible iPhone with enough battery to share.

Some public spaces — airports, coffee shops, libraries — have charging stations or USB outlets. Carrying a USB-C to Lightning cable (for iPhone 15 and 16) or a Lightning cable (for iPhone 14) takes up minimal space and gives you access to any power outlet. This is often faster and more convenient than wireless power sharing.

Frequently Asked Questions

Can I charge an iPhone 13 or older from an iPhone 15?

No. The receiving phone must also be iPhone 14 or newer. Older iPhones do not have the hardware to receive wireless power from another phone. You can still charge an older iPhone using a wall charger or portable battery pack.

Does wireless power sharing work through a phone case?

It depends on the case. Thin plastic or silicone cases usually allow the signal through. Thick cases, leather cases, or any case with metal components will block or weaken the connection. Remove the case and try again if charging does not start.

What if my iPhone gets too hot during wireless power sharing?

The phone will automatically pause the power transfer if it overheats. This is a safety feature and is not harmful. Move the phones to a cooler location, wait a few minutes, and try again. If overheating happens repeatedly, stop using wireless power sharing and use a wall charger instead.

Can I use wireless power sharing while using my phone?

You can, but it is not recommended. Using the phone while it is being charged wirelessly may interrupt the connection or cause the transfer to pause. Keep both phones still and avoid touching them while the transfer is in progress.

Is wireless power sharing faster than a standard charger?

No, it is much slower. A standard wall charger adds 15 to 20 percent per minute, while wireless power sharing adds only 1 to 2 percent per minute. Use wireless power sharing only for emergency top-ups when a charger is not available.