The Touch Smartwatch Gen 7 uses a magnetic charging dock, not a cable

The Touch Smartwatch Gen 7 charges through a small magnetic dock that attaches to the back of the watch. You do not plug in a cable or insert the watch into a cradle. Instead, you align the watch face-up on the dock, and magnets hold it in place while metal contacts on the back of the watch connect to charging pins on the dock.

This design means the charging port itself stays sealed, which reduces the chance of water or dust getting inside. The watch will show a charging icon on the screen — usually a lightning bolt or battery symbol — within a few seconds of being placed on the dock correctly.

Key Takeaways

  • The Touch Gen 7 charges on a magnetic dock that comes in the box; align the watch face-up and the magnets will snap it into place.
  • A full charge takes about 60 to 90 minutes from completely empty, depending on the watch model and charger used.
  • The watch should show a charging icon on screen within seconds; if it does not, rotate the watch slightly or check that the dock pins are clean.
  • Use the charger that came in the box or a certified replacement, as third-party docks may not align the contacts properly and can damage the watch back.
  • The watch battery lasts longer if you charge it before it drops below 20 percent, rather than waiting until it shuts off completely.

Setting up the magnetic dock for the first time

The charging dock comes with a USB cable attached or a separate USB-A to micro-USB cable, depending on which version of the Gen 7 you own. Plug the USB end into a wall adapter, a computer, or any device with a USB port. The dock itself has no on-off switch — it is ready to charge as soon as power reaches it.

Place the dock on a flat surface where it will not roll or tip. The charging pins should face upward. If your dock came with a small stand or base, attach it now so the dock sits at a slight angle; this makes it easier to see the watch screen while it charges and reduces strain on the magnetic connection if you bump the table.

How to place the watch on the dock correctly

Hold the watch with the screen facing up and the back facing down toward the dock. Slowly lower the watch toward the dock until you feel the magnets pull it into alignment. The watch should snap into place with a gentle click or snap feeling. You do not need to press hard or twist it.

Once the watch is on the dock, look at the screen. Within 2 to 5 seconds, you should see a charging icon appear — this is usually a lightning bolt, a plug symbol, or a battery with a plus sign. If you do not see this icon, lift the watch off and try again, rotating it slightly so the back contacts line up with the dock pins. If the icon still does not appear after two or three tries, check the dock pins for dirt or lint and wipe them gently with a dry cloth.

Charging time and battery percentage

A Touch Smartwatch Gen 7 that is completely empty takes about 60 to 90 minutes to reach a full charge. The exact time depends on whether you are using the original charger or a third-party USB adapter, and whether the watch is on or off during charging. Charging is slightly faster if you turn the watch off, but you can leave it on and use it normally while it charges.

The watch screen will show the battery percentage while charging. Most people charge overnight or while they are at a desk, so the exact timing matters less than making sure the watch is on the dock before the battery runs out. If the battery reaches zero, the watch will power off and the screen will go dark, but it will still charge once you place it back on the dock.

What to do if the watch will not charge

If the charging icon does not appear after you place the watch on the dock, start by checking the dock itself. Look at the two or three small metal pins on the dock surface. If they are dirty, dusty, or have lint stuck to them, wipe them gently with a dry, soft cloth or a cotton swab. Dirt on these pins is the most common reason a watch will not charge.

Next, check the back of the watch where the charging contacts are. These are small metal circles or rectangles on the watch back. Wipe them clean with a dry cloth as well. Then place the watch on the dock again, making sure it is centered and the back is flat against the dock surface.

If the watch still will not charge, try a different USB power source. Plug the dock into a different wall outlet, or connect it to a computer USB port instead. Some USB adapters do not provide enough power. If the watch charges with a different power source, the original adapter may be faulty. If it still does not charge with multiple power sources, the dock itself may be damaged and you may need a replacement.

Protecting the dock and charging contacts

The magnetic dock is durable, but the charging pins are small and can bend if the watch is dropped on the dock or if something heavy is placed on top of it. Store the dock in a safe place when you are not using it, and keep it away from the edge of a table or desk.

The metal contacts on the back of the watch can also get scratched or corroded if they are exposed to sweat, water, or dirt for long periods. Wipe the watch back dry after you exercise or swim, and wipe the dock dry if it gets wet. Do not use the dock in a bathroom where steam is heavy, and do not leave the watch on the dock in direct sunlight for hours at a time, as heat can damage the battery.

Using third-party chargers and what to avoid

The original Touch Smartwatch Gen 7 charger is designed specifically for the watch and aligns the contacts correctly. Third-party magnetic docks that claim to work with the Gen 7 may not align the pins in the same way, which can cause slow charging, incomplete charging, or damage to the watch back over time.

If you need a backup charger, look for one that is certified by the watch manufacturer or sold by the same brand. Avoid very cheap third-party docks from unknown sellers, as they often use weaker magnets that do not hold the watch securely, or pins that are spaced differently and do not make good contact with the watch.

Frequently Asked Questions

Can I charge the Touch Gen 7 with a wireless charger made for phones?

No. Phone wireless chargers use a different technology and will not charge a smartwatch. The Touch Gen 7 requires its specific magnetic dock. Using a phone charger will not damage the watch, but it straightforward will not work.

Is it safe to charge the watch overnight?

Yes. The Touch Gen 7 has built-in protection that stops charging once the battery reaches 100 percent, so leaving it on the dock overnight will not overcharge it or damage the battery. Many people charge their watch while they sleep.

Why does my watch charge slowly sometimes?

Slow charging usually means the contacts are dirty or the dock is not aligned properly. Clean both the dock pins and the watch back with a dry cloth. If you are using a low-power USB adapter, try a different power source. The watch also charges more slowly if it is very hot or very cold.

What should I do if the dock cable is damaged?

If the USB cable attached to the dock is frayed, cracked, or not working, you can replace just the cable if it is detachable. Check whether your dock has a removable cable or if the cable is permanently attached. If it is removable, buy a replacement USB-A to micro-USB cable. If it is attached, you will need to replace the entire dock.

Can I use the watch while it is charging?

Yes. The watch will stay on the dock and charge while you use it normally. You can check notifications, use apps, or view the time. The only downside is that the watch screen and features use battery power while charging, so it takes slightly longer to reach a full charge than if the watch were off.