Power on your headphones first, then enable noise cancelling
To use noise cancelling on Anker Soundcore headphones, you need to turn on the headphones themselves, then set up the noise cancelling feature through either a physical button or the Soundcore app. Most Soundcore models have a dedicated noise cancelling button on the earcup — usually marked with a microphone icon or labeled "ANC" — that toggles between noise cancelling on, noise cancelling off, and transparency mode (which lets outside sound in).
The exact steps depend on which Soundcore model you own, since Anker makes several versions with different button layouts. The most common models — Space A40, Space Q45, and Space Q30 — all follow the same basic process, though the button location varies slightly between them.
Key Takeaways
- Press and hold the power button on your Soundcore headphones for three seconds until you hear a startup sound or see a light indicator.
- Once powered on, press the noise cancelling button (usually on the right earcup) to cycle through noise cancelling on, off, and transparency mode.
- The Soundcore app lets you fine-tune noise cancelling strength and switch modes without using the physical button.
- Battery life with noise cancelling enabled is typically 8 to 12 hours depending on your model, compared to 15 to 20 hours with it off.
Locate the power button and noise cancelling button on your model
On Soundcore Space A40 and Space Q45 headphones, the power button is on the left earcup and the noise cancelling button is on the right earcup. The noise cancelling button is usually smaller and positioned toward the back of the earcup. On the Space Q30, both buttons are on the right side, with the power button on top and the noise cancelling button below it.
If you are unsure which button is which, check the quick-start guide that came with your headphones or look at the diagram on the inside of the box. Anker includes a visual layout showing button positions for your specific model. You can also find this information on Anker's support website by searching for your model number, which is printed on the bottom of the left earcup.
Power on your headphones
Press and hold the power button for three seconds. You will hear a chime or voice prompt saying "Power on" or similar, and an LED light on one or both earcups will turn on — usually blue or white. If the headphones have been off for a while, they may take a few seconds to fully boot up before the light appears.
If you do not hear anything or see a light, check that the battery is charged. Connect the headphones to a USB-C cable (or micro-USB on older models) and a power adapter for at least 15 minutes, then try again. A completely dead battery may take 30 minutes to show any sign of charging.
set up noise cancelling with the physical button
Once the headphones are on, press the noise cancelling button once. You will hear a tone or voice prompt indicating the mode has changed. The first press usually turns noise cancelling on. Press it again to cycle to transparency mode (ambient sound passes through). Press a third time to turn noise cancelling off completely. The cycle then repeats.
The LED light often changes color or blinks differently depending on which mode you are in — for example, solid blue for noise cancelling on, blinking blue for transparency mode, and off or dim for noise cancelling disabled. Check your manual to confirm the light pattern for your specific model, since this varies between Soundcore versions.
Use the Soundcore app to control noise cancelling
read the Soundcore app from the Apple App Store or Google Play Store and pair your headphones via Bluetooth. Open the app, tap the noise cancelling icon (usually at the bottom of the main screen), and you will see three options: Noise Cancelling On, Transparency Mode, and Noise Cancelling Off. Tap whichever mode you want.
The app also shows you a slider for noise cancelling strength on some models — you can adjust how aggressively the headphones cancel sound, from light to maximum. This is useful if you want to block airplane engine noise but still hear announcements, or if maximum cancelling feels uncomfortable in your ears. The app setting overrides the physical button until you restart the headphones.
Understand what noise cancelling actually blocks
Noise cancelling on Soundcore headphones works best on constant, low-frequency sounds like airplane engines, air conditioning hum, traffic noise, and washing machines. It is much less effective on sudden or high-pitched sounds like a dog barking, a car horn, or someone speaking directly to you. This is a limitation of the technology itself, not a flaw in Anker's design — all noise cancelling headphones work this way.
When noise cancelling is on, you may notice a slight hissing or pressure sensation in your ears, especially in very quiet rooms. This is normal and is caused by the active noise cancelling circuitry. If it bothers you, try transparency mode instead, or turn noise cancelling off and use the passive isolation from the earcup seal to block sound naturally.
Check battery drain and troubleshoot if noise cancelling will not turn on
Noise cancelling uses extra battery power — expect about 8 to 12 hours of listening time with it on, versus 15 to 20 hours with it off, depending on your model and volume level. If you are using your headphones all day, you may want to turn noise cancelling off during the last few hours to preserve battery.
If the noise cancelling button does not respond when you press it, first make sure the headphones are fully powered on — the LED should be lit. If the button still does not work, try restarting the headphones by holding the power button for five seconds until they shut down, then power them back on. If noise cancelling still will not set up, the headphones may need a firmware update through the Soundcore app, or the button itself may be stuck and need cleaning with a dry cloth.
Frequently Asked Questions
Does noise cancelling work if the headphones are not connected to my phone?
Yes. Noise cancelling is a hardware feature that works independently of Bluetooth or any app. You can turn it on using the physical button even if the headphones are not paired to anything. However, you cannot adjust the noise cancelling strength without the app — you can only cycle between on, off, and transparency mode.
Why does noise cancelling sound like it is making a hissing noise?
The hissing is the active noise cancelling circuitry at work. It is most noticeable in very quiet environments or when no music is playing. This is normal and happens on most noise cancelling headphones. If it bothers you, try playing music at a low volume, use transparency mode instead, or turn noise cancelling off entirely.
Can I use noise cancelling and transparency mode at the same time?
No. You can only use one mode at a time — either noise cancelling on, transparency mode, or noise cancelling off. Transparency mode lets outside sound in but does not actively cancel it. If you want to hear your surroundings while also blocking some noise, transparency mode is your best option.
What should I do if the noise cancelling button is stuck or not responding?
Try restarting the headphones by holding the power button for five seconds. If the button still does not work, gently clean around the button with a dry cloth to remove any debris. If it remains stuck, check the Soundcore app to see if a firmware update is available — sometimes a software update fixes button responsiveness issues.
Does turning off noise cancelling really save that much battery?
Yes, typically 5 to 8 extra hours of listening time. If your headphones normally last 12 hours with noise cancelling on, they will last around 18 to 20 hours with it off. The exact difference depends on your model and how loud you play music, but noise cancelling is one of the biggest battery drains in wireless headphones.