Pairing a single replacement AirPod works differently than the original setup
When you replace one AirPod, you do not start over with the full pairing process. Instead, you place the new AirPod in the charging case with your existing one, hold the setup button on the back of the case for 15 seconds until the light flashes amber, then white, and your device will recognize it as part of the same pair. The whole process takes about two minutes and works on iPhone, iPad, Mac, and Android devices.
The key difference from initial setup is that your device already knows your original AirPod. When you introduce the replacement, your device straightforward adds it to the existing connection rather than creating a new one from scratch. This is why you need both AirPods in the case together during the pairing step — your device needs to see them as a matched pair.
Key Takeaways
- Place the new AirPod in the charging case alongside your existing AirPod before you start pairing.
- Press and hold the setup button on the back of the case for 15 seconds until you see the light flash amber, then white.
- Your device will show a pairing notification on screen; tap "Connect" or "Pair" to complete the process.
- If pairing fails, reset both AirPods by holding the setup button for 15 seconds after the light turns white, then try again.
Step-by-step pairing on iPhone or iPad
Open the lid of your charging case with both the new and existing AirPod inside. On your iPhone or iPad, go to Settings, then tap Bluetooth. You should see your AirPods listed. If they are already connected, tap the information icon (the small "i" in a circle) next to the AirPods name.
While you have the Bluetooth settings open, press and hold the setup button on the back of your charging case for 15 seconds. The light inside the case will flash amber for a few seconds, then turn white. This signals that the case is in pairing mode. Your iPhone or iPad will show a pairing notification on screen. Tap Connect to complete the pairing. Your device will confirm that both AirPods are now connected.
If you do not see a pairing notification, make sure Bluetooth is turned on and that you are holding the setup button long enough. The 15-second count matters — if you release too early, the pairing mode will not set up.
Pairing on Mac
On your Mac, click the Apple menu in the top-left corner and select System Settings (or System Preferences on older versions). Click Bluetooth in the sidebar. Open the lid of your charging case with both AirPods inside, and press and hold the setup button on the back of the case for 15 seconds until the light flashes white.
Your Mac will show your AirPods in the Bluetooth list with a Connect button. Click that button to pair the replacement AirPod with your existing one. Once connected, your Mac will remember this pairing and connect automatically the next time you open the case near your computer.
Pairing on Android devices
Android pairing works the same way as iPhone, but the settings menu looks different. Open Settings on your Android phone or tablet, then go to Bluetooth or Connected Devices (the exact name varies by manufacturer). Open the lid of your charging case with both AirPods inside.
Press and hold the setup button on the back of the case for 15 seconds until the light flashes white. Your Android device will show your AirPods in the available devices list. Tap the AirPods name to pair them. If your AirPods were already paired to this Android device, you may see them listed as already connected — in that case, the new AirPod will straightforward join the existing connection without any additional steps needed.
What to do if pairing fails
If the pairing notification does not appear after 15 seconds, or if your device shows an error, the most common fix is to reset the AirPods. With both AirPods in the case, press and hold the setup button for 15 seconds after the light turns white (not amber). Keep holding until the light flashes amber again. This resets the case and both AirPods to factory settings.
After a reset, close the case, wait 10 seconds, then open it again and repeat the pairing steps from the beginning. If you still see no pairing notification, check that Bluetooth is turned on in your device settings and that you are within 10 feet of your phone or computer. Walls and other devices can sometimes interfere with the Bluetooth signal, so move to an open area and try again.
If the replacement AirPod still will not pair after a reset, the AirPod itself may be defective. Contact Apple Support with your proof of purchase — they can verify whether the AirPod is faulty and send a replacement.
Pairing the same replacement AirPod to multiple devices
Once you have paired your replacement AirPod to one device, you can add it to other devices you own. On your second device, open Bluetooth settings and press and hold the setup button on the case for 15 seconds until the light flashes white. Your second device will show the AirPods in the pairing list. Tap to connect.
Your AirPods will now be paired to both devices. When you open the case near either device, the AirPods will connect to whichever one you used most recently. If you want to switch to a different device, open Bluetooth settings on that device and tap your AirPods to reconnect.
Removing the old AirPod from your device
If you are replacing a damaged AirPod and want to remove the old one from your device's memory, you can do this through Bluetooth settings. On iPhone or iPad, go to Settings > Bluetooth, tap the information icon next to your AirPods, and select Forget This Device. On Mac, go to System Settings > Bluetooth, click the information icon next to your AirPods, and select Remove. On Android, go to Settings > Bluetooth, tap and hold your AirPods, and select Forget or Unpair.
After you forget the old pairing, you can then pair your replacement AirPod as if it were a brand-new pair. This is useful if the old AirPod is lost or broken and you want a clean start, but it is not necessary if you straightforward want to add a replacement to an existing pair.
Frequently Asked Questions
Do I need to reset my device before pairing a replacement AirPod?
No. Your device does not need to be reset. The pairing process adds the new AirPod to your existing connection, so your device settings and preferences stay the same. You only need to reset the AirPods themselves if pairing fails on the first attempt.
What if my replacement AirPod is not charging in the case?
Check that the metal contacts on the bottom of the AirPod are clean and making contact with the case. Wipe both the AirPod and the inside of the case with a dry, lint-free cloth. If the AirPod still will not charge, the case itself may need cleaning or replacement. Try charging the case with a different USB cable first to rule out a cable problem.
Can I pair a replacement AirPod if I lost the original one?
Yes. If you have lost one AirPod and only have the case and one remaining AirPod, you can still pair a replacement. Put the new AirPod in the case with the old one and follow the standard pairing steps. Both will pair together as a matched set.
Will my replacement AirPod work with my old charging case?
Yes. Replacement AirPods are designed to work with any charging case from the same generation. Make sure your replacement matches the generation of your existing AirPod — AirPods Pro, AirPods Max, and standard AirPods all use different cases and are not interchangeable.