The simplest way to add sound to your monitor

Most monitors have a 3.5mm audio jack (the small round port) on the back, and you can plug speakers directly into it using a standard audio cable. If your monitor has no audio jack, you can run a cable from your computer's headphone port or audio output instead. The monitor method works best because the audio signal travels through the same cable as your video, so you only manage one connection.

Before you buy speakers, check what ports your monitor actually has. Look at the back panel — you are looking for a port labeled "audio out," "headphone," or showing a speaker symbol. If you see nothing, your monitor does not have audio output, and you will need to connect speakers to your computer directly instead.

Key Takeaways

  • Most monitors have a 3.5mm audio jack on the back where you can plug speakers in directly using a standard audio cable.
  • If your monitor has no audio jack, connect speakers to your computer's headphone port or audio output port instead.
  • You may need to tell your computer to send sound through the monitor rather than its own speakers, which takes 30 seconds in your sound settings.
  • Powered speakers (with their own power cord) work with any monitor; passive speakers need an amplifier and are rarely used for monitors.
  • If sound still does not come through, check that the cable is plugged in fully, the volume is turned up on both the speakers and your computer, and the correct audio output is selected.

What cable and speakers you actually need

You need two things: a 3.5mm audio cable (also called an aux cable or headphone cable) and powered speakers. Powered speakers have a power cord and volume knob built in, so they work when ready when you plug them in. They cost between $20 and $150 depending on size and sound quality. Do not buy passive speakers — those require a separate amplifier and are not practical for monitor setups.

The audio cable itself is inexpensive and comes in different lengths. A 6-foot cable is standard and reaches most monitor-to-speaker distances. Both ends of the cable look identical — a small round connector about the width of a pencil. One end plugs into your monitor's audio jack, the other into the speakers' audio input (usually labeled "audio in" or "line in").

If your monitor has no audio jack but your computer does, buy the same cable and plug one end into your computer's headphone port instead. Your computer will treat the speakers the same way it treats headphones.

Connecting the cable step by step

Turn off your monitor and speakers before you plug anything in. This is not strictly necessary, but it prevents any electrical pop that might damage the speakers.

Locate the audio jack on the back of your monitor. It is usually near the bottom, often grouped with other ports. If you cannot find it, check your monitor's manual — search the model number online plus the word "manual" and you will find a PDF showing every port.

Plug one end of the 3.5mm cable into the monitor's audio jack. Push it in until you feel it click or seat fully. Plug the other end into the audio input on your speakers. Again, push until it is fully seated. Loose connections are the most common reason sound does not work.

Turn the speakers on. You should see a light on the speaker unit, usually green or blue. Turn the volume knob on the speakers to about 25 percent — not all the way up. Then turn on your monitor and computer.

Telling your computer to send sound through the monitor

Once the cable is plugged in, your computer may not automatically send sound through the speakers. You need to tell it which audio output to use. This takes less than a minute.

On Windows: Right-click the speaker icon in the bottom right corner of your screen (in the system tray). Click "Open Volume mixer" or "Sound settings." Look for a section called "Output" or "Playback devices." You should see your monitor listed — it may say the monitor model name or "HDMI" or "Digital Audio." Click on it and then click "Set as default." Close the window. Sound should now play through the speakers.

On Mac: Click the Apple menu in the top left, then "System Settings" or "System Preferences." Click "Sound." Click the "Output" tab. Look for your monitor in the list — it may say the monitor name or "HDMI." Click on it. Close the window. Sound should now play through the speakers.

If you do not see your monitor listed as an output option, the cable may not be fully plugged in, or your monitor may not have audio output. Unplug the cable, push it in harder, and try again. If it still does not appear, your monitor does not have audio output, and you will need to connect speakers to your computer instead.

Adjusting volume so it sounds right

Sound volume has three places to control: your computer's volume, the speakers' volume knob, and the volume of whatever program is playing (like a video or music app). All three affect the final loudness.

Start with the speakers' volume knob at about 25 to 30 percent. Then use your computer's volume control (the speaker icon in the system tray on Windows, or the volume icon in the menu bar on Mac) to set the overall level. If the sound is still too quiet, turn up the speakers' knob a bit more. If it is too loud, turn down the speakers' knob first — this gives you finer control than the computer volume.

Never turn the speakers' volume all the way up and then control everything from the computer. This can cause distortion and makes it harder to hear quiet sounds. A good starting point is speakers at 40 to 50 percent and computer volume at 60 to 70 percent.

When the monitor has no audio jack

Some monitors, especially older ones or very basic models, have no audio output at all. If you looked at the back and found no audio jack, you have two options.

The first option is to connect speakers to your computer's audio output instead. Most computers have a headphone jack on the front or back. Plug the 3.5mm cable into that port, then into the speakers. Your computer will automatically send sound there. This works just as well as using the monitor — the only difference is you manage one more cable.

The second option is to buy a monitor with audio output. If you are shopping for a new monitor anyway, look for one with a 3.5mm audio jack listed in the specifications. Many mid-range and larger monitors include this feature.

Troubleshooting when sound does not come through

No sound at all: First, check that the cable is pushed in fully on both ends — wiggle it slightly to make sure it is seated. Then check that the speakers are turned on (look for a power light). Turn up the volume knob on the speakers to at least 50 percent. On your computer, check that the volume is not muted (look at the speaker icon in the system tray or menu bar) and that the correct audio output is selected in your sound settings.

Sound comes from computer speakers instead of the monitor speakers: Your computer is still sending sound to its built-in speakers. Go back to your sound settings and make sure you selected the monitor as the default output. On Windows, right-click the speaker icon and open Sound settings. On Mac, go to System Settings and click Sound. Select your monitor from the output list.

Sound is very quiet even with volume turned up: Check that both the speakers' volume knob and your computer's volume are above 50 percent. If the cable is very long (over 20 feet), it may be picking up interference — try moving the cable away from power cords or other electronics. If the problem persists, the speakers may be faulty.

Sound cuts out or crackles: This usually means the cable is not fully plugged in or is loose. Unplug both ends, inspect the connectors for dirt, and plug them back in firmly. If crackling continues, try a different audio cable — the original may be damaged.

Frequently Asked Questions

Can I use wireless speakers with my monitor?

Yes, but you need to connect them to your computer, not the monitor. Bluetooth speakers pair with your computer the same way they pair with a phone. Go to your computer's Bluetooth settings, put the speakers in pairing mode, and select them from the list. USB speakers also work — just plug them into a USB port on your computer.

Do I need powered speakers or can I use passive ones?

You need powered speakers. Passive speakers require a separate amplifier, which adds cost and complexity. Powered speakers have the amplifier built in and work when ready when you plug them in and turn them on.

What if my monitor uses DisplayPort or USB-C instead of HDMI?

The audio jack is separate from the video port. Look for a 3.5mm jack on the monitor's back panel regardless of which video cable you use. If your monitor has no audio jack, connect speakers to your computer's audio output instead.

Can I connect multiple speakers to one monitor?

Not directly — a monitor has only one audio output. You can buy powered speakers with multiple inputs and switch between them, or you can connect one pair of speakers and run audio from them to a second pair using a splitter cable, though this reduces sound quality.

Will connecting speakers to my monitor affect my video quality?

No. The audio cable is completely separate from the video cable. Adding speakers changes nothing about how your monitor displays the picture.