Pairing Beats Solo 3 to iPhone for the first time
Turn on your Beats Solo 3 by sliding the power switch on the left ear cup toward the Beats logo. The headphones will enter pairing mode automatically if they have never been connected to a device before — you will see a blue and red LED light flashing on the left ear cup. On your iPhone, go to Settings, then Bluetooth, and turn Bluetooth on. Your iPhone will show "Beats Solo3" in the list of available devices. Tap it to connect.
If the headphones do not appear in your Bluetooth list, hold down the power button for 10 seconds until you see the LED flash red and blue together. This forces the headphones back into pairing mode. Then try searching again on your iPhone.
Once connected, you will see a checkmark next to "Beats Solo3" in your Bluetooth settings, and the LED on the headphones will turn solid blue. Your iPhone will remember these headphones and reconnect automatically the next time you turn them on and Bluetooth is enabled on your phone.
Key Takeaways
- Turn on the headphones and look for a flashing blue and red LED light, which means they are ready to pair with your iPhone.
- Go to Settings > Bluetooth on your iPhone, turn Bluetooth on, and tap "Beats Solo3" from the available devices list.
- If pairing fails, hold the power button for 10 seconds to reset the headphones and try again.
- Once paired, your iPhone will reconnect to the headphones automatically whenever both devices have Bluetooth turned on.
- You can connect the same Beats Solo 3 to multiple Apple devices, but they will only play audio from one device at a time.
Reconnecting after the initial pairing
After the first pairing, you do not need to repeat the setup process. straightforward turn on your Beats Solo 3 and make sure Bluetooth is on in your iPhone's Settings. The headphones will connect within a few seconds. You will hear a tone in the headphones when the connection is successful.
If your iPhone does not reconnect automatically, open Settings > Bluetooth and tap "Beats Solo3" manually. If the headphones still do not appear, restart Bluetooth on your iPhone by turning it off and back on in Settings, then try again.
Connecting to a different iPhone or Apple device
Beats Solo 3 can be paired to multiple devices at once, but they will only play audio from one at a time. To switch which device is playing through the headphones, go to Bluetooth settings on the new device and tap "Beats Solo3" to connect. The headphones will disconnect from the previous device and connect to the new one.
If you want to unpair the headphones from an iPhone completely, go to Settings > Bluetooth, find "Beats Solo3" in the list, tap the information icon next to it, and select "Forget This Device." You will then need to pair them again from scratch the next time you want to use them with that iPhone.
Checking battery and connection status
The LED light on the left ear cup tells you the connection and battery status. A solid blue light means the headphones are connected and have good battery. A flashing blue light means they are connected but the battery is low — usually below 20 percent. A red light means the battery is critically low and the headphones will shut off soon.
You can also check the battery percentage on your iPhone. When the headphones are connected, swipe down from the top right corner of your screen to open Control Center, and you will see the battery level of your Beats Solo 3 displayed alongside your iPhone's battery.
Troubleshooting connection problems
If your Beats Solo 3 will not connect to your iPhone, first make sure both devices have Bluetooth turned on. Then restart both devices — turn off the headphones completely, wait 10 seconds, and turn them back on. Restart your iPhone by powering it off and back on as well.
If the headphones still will not pair, reset them to factory settings. Hold down the power button for 15 seconds until you see the LED flash red, then release. The headphones are now reset and will enter pairing mode. Try pairing with your iPhone again from the Bluetooth settings.
If you see "Beats Solo3" in your Bluetooth list but it says "Not Connected" or "Unable to Connect," tap the information icon next to it and select "Forget This Device." Then restart Bluetooth on your iPhone and pair the headphones fresh.
Using Siri with your Beats Solo 3
Once your Beats Solo 3 are connected to your iPhone, you can use Siri hands-free. Press and hold the center button on the right ear cup for about two seconds. Siri will set up and you will hear a tone. You can then speak commands like "play music," "call Mom," or "what is the weather." Release the button when you are done speaking.
You can also set up Siri by saying "Hey Siri" if you have enabled this feature in Settings > Siri & Search on your iPhone. This works whether or not you are holding the button, as long as the headphones are connected.
Frequently Asked Questions
Why does my iPhone not see my Beats Solo 3 in Bluetooth settings?
The headphones may not be in pairing mode. Turn them on and look for a flashing blue and red LED light. If you only see a solid blue light, hold the power button for 10 seconds to force pairing mode. Also check that Bluetooth is turned on in your iPhone's Settings.
Can I use Beats Solo 3 with multiple iPhones at the same time?
The headphones can be paired to multiple devices, but they will only play audio from one at a time. To switch, open Bluetooth settings on the new iPhone and tap "Beats Solo3." The connection will move to that device automatically.
How do I know if my Beats Solo 3 are fully charged?
A solid blue LED light indicates the headphones are connected and charged. You can also check the battery percentage in your iPhone's Control Center when the headphones are connected. Charge the headphones using the included USB-C cable until the LED turns off, which means they are fully charged.
What should I do if my Beats Solo 3 keep disconnecting from my iPhone?
First, forget the device in Bluetooth settings and pair them fresh. If disconnections continue, restart your iPhone and update to the latest iOS version in Settings > General > Software Update. Also make sure the headphones have a full charge, as low battery can cause connection drops.
Can I use Beats Solo 3 with non-Apple phones?
Yes, Beats Solo 3 use standard Bluetooth and work with Android phones, Windows devices, and other Bluetooth-enabled devices. The pairing process is the same — turn on the headphones, enable Bluetooth on your device, and select "Beats Solo3" from the available devices list.