Wired headphones plug directly into your iPhone's charging port or headphone jack, while wireless headphones pair through Bluetooth settings
The method depends on what type of headphones you own. iPhones from iPhone 6s onward have no headphone jack, so wired headphones must use a Lightning connector (the charging port) or a USB-C connector on newer models. Wireless headphones connect through Bluetooth, which is built into every iPhone. Both methods work equally well — the choice comes down to what you already own and whether you want to charge your phone while listening.
The connection process takes less than a minute for either type. Once connected, your iPhone remembers the headphones and reconnects automatically the next time they're nearby and turned on.
Key Takeaways
- Wired headphones with a Lightning or USB-C connector plug directly into your iPhone's charging port and work when ready without pairing.
- Wireless headphones connect through Bluetooth by holding down the pairing button until a light flashes, then selecting them in iPhone Settings under Bluetooth.
- Your iPhone remembers wireless headphones after the first connection and reconnects automatically when they're powered on and nearby.
- If wireless headphones won't connect, forget them in Bluetooth settings and pair them again from the beginning.
- You can connect multiple pairs of headphones to your iPhone, but only one pair can play audio at the same time.
Connecting wired headphones with a Lightning or USB-C connector
Plug the connector end into your iPhone's charging port at the bottom. The headphones will work when ready — no setup needed. Your iPhone recognizes them as soon as they make contact.
If your headphones came with an adapter (a small piece that converts one connector type to another), use that adapter between the headphones and your phone. Some older wired headphones use a 3.5mm jack and require a separate Lightning-to-3.5mm adapter, which you can buy from Apple or third-party manufacturers.
One limitation: you cannot charge your iPhone and use wired headphones at the same time unless your headphones have a pass-through charging port built in. Most do not. If you need to charge while listening, wireless headphones are the better choice.
Pairing wireless headphones through Bluetooth
Turn on your headphones and hold down the pairing button until you see a flashing light — usually white or blue. The light indicates the headphones are in pairing mode and searching for a device to connect to. This typically takes 3 to 5 seconds of holding the button.
On your iPhone, open Settings and tap Bluetooth. Make sure Bluetooth is turned on (the toggle at the top should be green). Your headphones should appear in the list under "Available Devices" within a few seconds. Tap the name of your headphones to connect.
Once connected, the headphones will show under "My Devices" with a checkmark. Your iPhone will now automatically reconnect to these headphones whenever they're powered on and within range (typically 30 feet). You do not need to repeat the pairing process unless you forget the headphones or pair them with a different device.
What to do if your wireless headphones won't pair
If your headphones don't appear in the Available Devices list, restart both the headphones and your iPhone. Turn off the headphones completely, wait 10 seconds, then turn them back on. Restart your iPhone by holding down the power button and side button together, then sliding to power off.
If they still won't pair, your headphones may already be paired with another device. Check whether they're connected to a laptop, tablet, or another phone. Disconnect them from that device first, then try pairing with your iPhone again. Most headphones can only connect to one device at a time.
If you've already paired the headphones with your iPhone before but they won't reconnect, forget them and pair again. Go to Settings > Bluetooth, find the headphones under "My Devices," tap the information icon (i) next to their name, and select "Forget This Device." Then repeat the pairing steps above.
Switching between multiple pairs of headphones
Your iPhone can remember many pairs of headphones, but only one pair can play audio at a time. If you have multiple wireless headphones paired, your iPhone will connect to whichever pair you turn on first. If two pairs are on simultaneously, your iPhone connects to the one it paired with most recently.
To switch to a different pair, turn off the currently connected headphones and turn on the pair you want to use. Your iPhone will disconnect from the first pair and connect to the second within a few seconds. You can also manually select which headphones to use by opening Control Center (swipe down from the top right), tapping the audio card, and choosing a different device from the list.
Checking battery and connection status
For wireless headphones, your iPhone displays the battery percentage in the Bluetooth settings. Go to Settings > Bluetooth and look at the percentage shown next to your headphones' name. Some iPhones also show a battery widget on the home screen if you add it — swipe right to see your widgets, tap "Edit," and add the Batteries widget.
If your headphones are connected but producing no sound, check the volume on both your iPhone and the headphones themselves. Some headphones have a physical volume dial or buttons. Also verify that the headphones are actually selected as the audio output device — open Control Center and confirm the audio card shows your headphones' name.
Using headphones with Siri and phone calls
Once headphones are connected, Siri will use them for voice input and output. Press and hold the home button (or say "Hey Siri") and speak your command. Your voice goes through the headphones' microphone, and Siri's response plays through the speakers.
Incoming calls will ring through your headphones if they're connected. Answer by tapping the answer button on the headphones themselves, or use the on-screen controls on your iPhone. Most wireless headphones have a dedicated button for answering and ending calls. If your headphones don't have a microphone, calls will still ring through the speakers, but you'll need to use your iPhone's microphone to speak.
Frequently Asked Questions
Can I use headphones with an older iPhone that has a headphone jack?
Yes. iPhones with a 3.5mm headphone jack (iPhone 6s and earlier) accept standard wired headphones with a 3.5mm connector directly. No adapter needed. Wireless headphones pair the same way through Bluetooth settings.
Why do my wireless headphones keep disconnecting?
Interference from other devices, low battery, or being out of range are common causes. Keep your headphones charged above 20 percent and within 30 feet of your iPhone. If interference is the problem, move away from Wi-Fi routers or other Bluetooth devices. Forgetting and re-pairing the headphones often fixes persistent disconnection issues.
Do I need to turn off Bluetooth when I'm not using wireless headphones?
No, but turning it off saves battery. Bluetooth uses minimal power when no headphones are connected, so leaving it on is fine if you use wireless headphones regularly. If you rarely use them, turning off Bluetooth extends your iPhone's battery life slightly.
Can I connect headphones to my iPhone while using a case?
Yes. Wired headphones plug into the charging port, which is accessible even with most cases. Wireless headphones don't require a physical connection, so a case makes no difference. If your case blocks the charging port, you may need to remove it or use a case with a cutout.
What if my headphones work with my iPhone but the microphone doesn't?
Check that your iPhone has permission to use the headphones' microphone. Go to Settings > Privacy > Microphone and make sure the app you're using (like Phone or a messaging app) is toggled on. Also verify the headphones' microphone isn't muted — many have a physical mute switch. If the microphone still doesn't work, try forgetting and re-pairing the headphones.